Neoprene, CR in ISO 1629 terms, sits between nitrile and EPDM: good weather resistance, moderate oil resistance, and a toughness that neither of them quite matches at the same price. It is the compound for outdoor equipment that also sees oil, and for refrigeration plant where the refrigerant and the lubricant arrive together.
It is a compromise, and the page should say so. Neoprene is not as oil resistant as NBR, not as weather resistant as EPDM, and not as heat resistant as either. What it does is cover the middle of all three, which is what a general purpose outdoor machine needs.
What Neoprene Is
Neoprene is polychloroprene, polymerised from chloroprene. The chlorine in the chain gives it resistance to ozone, weather and flame, and it also makes the compound polar enough to resist non polar oils to a degree, which EPDM cannot do. Crystallisation on standing gives it useful strength without vulcanisation, and it is why a neoprene ring feels stiffer than an NBR one of the same hardness.
Properties At A Glance
The figures below are typical for a 70 Shore A compound of this class, which is the hardness most of our stock and most drawings call for. A 90 Shore A version of the same polymer will sit at the top of the hardness range and at the bottom of the temperature range.
| Property | Typical value | What it means |
|---|---|---|
| Hardness | 40 to 90 Shore A | 70 for general service |
| Temperature range | −40 to +120 °C | Low temperature grades to −50 °C |
| Colour | Black | Also available in grey and white for food grades |
| Tensile strength | 10 to 18 MPa | The highest tear strength of the five |
| Compression set | Fair | Weaker than NBR at the same temperature |
| Weather and ozone | Excellent | Behind EPDM but far ahead of NBR |
| Relative cost | Low to moderate | Slightly above NBR |
Where It Works
- Outdoor equipment that also sees oil or grease
- Refrigeration and air conditioning, with CFC and HFC refrigerants and their oils
- Water and seawater at moderate temperature
- Dilute acids and bases where NBR would harden
- Joints that need abrasion resistance, such as a rod wiper or a cover seal
Where It Fails
- Aromatic solvents, ketones and esters
- Hot water and steam above about 100 °C
- Petrol and aromatic fuel, where swelling is significant
- Continuous service above 120 °C, where it hardens and takes a set
- Highly polar solvents, where the chlorine in the chain offers no protection
Resistance To Common Media
Ratings are for the compound class at room temperature unless the note says otherwise, and they describe swelling, hardening and loss of strength together rather than one figure. A compound that swells 20 percent has already changed its squeeze.
| Medium | Rating | In practice |
|---|---|---|
| Refrigerant with mineral or POE oil | Good | The classic refrigeration seal |
| Mineral oil and grease | Good | Not as good as NBR; check swell |
| Water and seawater | Good | To about 90 °C |
| Ozone and weather | Excellent | Suitable for exposed outdoor joints |
| Petrol and diesel | Fair | Swells more than NBR |
| Aromatic solvents | Poor | Toluene and xylene swell it badly |
| Ketones and esters | Poor | Not a solvent compound |
| Dilute acids and bases | Good | Better than NBR on both |
Compounds We Quote
We quote neoprene from 40 to 90 Shore A, in general purpose and low temperature grades. Food contact grades to FDA 21 CFR 177.2600 are available on request. Neoprene is also the compound we use for fabric reinforced diaphragms, where its combination of flex life and oil resistance matters more than any single figure on a data sheet.
If the joint is outdoor and oil free, EPDM is the better and usually cheaper choice. If it is oil only, NBR wins. Neoprene earns its place where both conditions apply at once, and where a buyer wants one compound across a range of machines rather than three.
Sizes And Standards
Choosing between compounds rather than specifying one? The O-ring material comparison puts all five side by side at 70 Shore A, with the temperature range and the media each one cannot take.
The size is a separate decision from the compound, and it is the one buyers most often get wrong. The four standard lists are on their own pages, each with a lookup that takes either the code or a pair of measured dimensions: AS568 (inch dash numbers), ISO 3601 (Class A and Class B metric), JIS B 2401 (P, G, S, SS and V series) and BS 1806 (British imperial numbers). If the drawing gives a size outside those lists, or a cord that is not standard, we mould to drawing.
What To Send With An Enquiry
- The size or dash number, and the standard it comes from
- The medium, and whether oil and weather both apply
- The temperature range, including the coldest start-up
- Hardness, and whether the seal is static or dynamic
- Whether the joint is a refrigerant circuit, where the lubricant matters as much as the gas
Is neoprene good for refrigeration?
Yes, with the right lubricant. Neoprene has been the standard seal for CFC and HFC circuits running mineral or POE oil. It is not a ammonia compound, and it is not the first choice for a CO2 system, so send the refrigerant rather than the application.
Neoprene or EPDM for outdoor use?
EPDM if there is no oil anywhere near the joint, because it weathers better and costs less. Neoprene where oil or grease is present, since EPDM would swell.
What temperature can neoprene take?
About 120 °C continuous, with low temperature grades reaching −50 °C. Above 120 °C it hardens and takes a compression set faster than NBR.
Is neoprene still available?
Yes, though the polymer has fewer suppliers than it did thirty years ago. We quote it in the same hardness range as the other compounds, and for diaphragms it remains one of the most used materials.
