JIS B 2401 O-Ring Size Chart: P, G, S, SS and V Series

JIS B 2401 groups its O-rings by what the ring does rather than by cross section alone, which is why a Japanese drawing carries a series letter as well as a number. The five series differ in cord range and in the groove they are meant for, and the number after the letter is a nominal figure rather than a measurement.

That last point is where most non-Japanese buyers lose a size. P22 is not a 22 mm inside diameter. It is 21.80 mm, with a 2.40 mm cord. P10 is 9.80 mm. Read the number as a metric dimension and the ring will not fit the groove, so this page gives the measured inside diameter and cross section for every code, and a lookup that accepts either the code or the dimensions you measured.

The Five Series

Series What it is used for Cord (mm) Codes in this chart Sizes
P General purpose, dynamic and static seals 1.90 to 8.40 P3 to P500 153
G Fixed and static joints, where the groove is rigid 3.10 and 5.70 G25 to G500 87
S Small cross sections for light housings 1.50 and 2.00 S3 to S150 66
SS Miniature rings for instruments and small fittings 1.00 SS005 to SS200 48
V Large diameter rings, including vacuum service 4.00 V15 to V150 10

The letters are not interchangeable. A P ring and a G ring can share an inside diameter and still take different cords, and the S and SS series exist because a 1.90 mm cord will not seat in a housing with a 1.4 mm groove width.

The Number Is Not The Inside Diameter

Each series offsets the code from the size in its own way, and the offset is a convention of the standard rather than a rounding error. Six examples show the range of it.

Code Inside diameter (mm) Cross section (mm) Outside diameter (mm) Reading the code as a size would give
P10 9.80 1.90 13.60 10.00, wrong by 0.20 mm
P22 21.80 2.40 26.60 22.00, wrong by 0.20 mm
G25 24.40 3.10 30.60 25.00, wrong by 0.60 mm
S10 9.50 1.50 12.50 10.00, wrong by 0.50 mm
SS100 10.00 1.00 12.00 10.00, correct by coincidence
V70 69.00 4.00 77.00 70.00, wrong by 1.00 mm

The gaps are smaller than the tolerance on a large groove and larger than the tolerance on a small one, which is why a misread code can be fitted and still leak. Where a drawing gives both the code and the dimension, the dimension is the one to work to.

JIS B 2401 Size Chart

Every size below is listed by code with its measured inside diameter, cross section and outside diameter in millimetres. The chart covers the P series to P500, the G series to G500, the full S and SS ranges and the V series to V150, which is the range we quote most often. For codes above these, send the number and we will confirm the size and the tooling position.

JIS code CS (mm) ID (mm) OD (mm) Quote
P3 1.90 2.80 6.60 +
P4 1.90 3.80 7.60 +
P5 1.90 4.80 8.60 +
P6 1.90 5.80 9.60 +
P7 1.90 6.80 10.60 +
P8 1.90 7.80 11.60 +
P9 1.90 8.80 12.60 +
P10 1.90 9.80 13.60 +
P10A 2.40 9.80 14.60 +
P11 2.40 10.80 15.60 +
P11.2 2.40 11.00 15.80 +
P12 2.40 11.80 16.60 +
P12.5 2.40 12.30 17.10 +
P14 2.40 13.80 18.60 +
P15 2.40 14.80 19.60 +
P16 2.40 15.80 20.60 +
P18 2.40 17.80 22.60 +
P20 2.40 19.80 24.60 +
P21 2.40 20.80 25.60 +
P22 2.40 21.80 26.60 +
P22.4 3.50 22.10 29.10 +
P22A 3.50 21.70 28.70 +
P24 3.50 23.70 30.70 +
P25 3.50 24.70 31.70 +
P25.5 3.50 25.20 32.20 +
P26 3.50 25.70 32.70 +
P28 3.50 27.70 34.70 +
P29 3.50 28.70 35.70 +
P29.5 3.50 29.20 36.20 +
P30 3.50 29.70 36.70 +
P31 3.50 30.70 37.70 +
P31.5 3.50 31.20 38.20 +
P32 3.50 31.70 38.70 +
P34 3.50 33.70 40.70 +
P35 3.50 34.70 41.70 +
P35.5 3.50 35.20 42.20 +
P36 3.50 35.70 42.70 +
P38 3.50 37.70 44.70 +
P39 3.50 38.70 45.70 +
P40 3.50 39.70 46.70 +
P41 3.50 40.70 47.70 +
P42 3.50 41.70 48.70 +
P44 3.50 43.70 50.70 +
P45 3.50 44.70 51.70 +
P46 3.50 45.70 52.70 +
P48 3.50 47.70 54.70 +
P48A 5.70 47.60 59.00 +
P49 3.50 48.70 55.70 +
P50 3.50 49.70 56.70 +
P50A 5.70 49.60 61.00 +
P52 5.70 51.60 63.00 +
P53 5.70 52.60 64.00 +
P55 5.70 54.60 66.00 +
P56 5.70 55.60 67.00 +
P58 5.70 57.60 69.00 +
P60 5.70 59.60 71.00 +
P62 5.70 61.60 73.00 +
P63 5.70 62.60 74.00 +
P65 5.70 64.60 76.00 +
P67 5.70 66.60 78.00 +
P70 5.70 69.60 81.00 +
P71 5.70 70.60 82.00 +
P75 5.70 74.60 86.00 +
P80 5.70 79.60 91.00 +
P85 5.70 84.60 96.00 +
P90 5.70 89.60 101.00 +
P95 5.70 94.60 106.00 +
P100 5.70 99.60 111.00 +
P102 5.70 101.60 113.00 +
P105 5.70 104.60 116.00 +
P110 5.70 109.60 121.00 +
P112 5.70 111.60 123.00 +
P115 5.70 114.60 126.00 +
P120 5.70 119.60 131.00 +
P125 5.70 124.60 136.00 +
P130 5.70 129.60 141.00 +
P132 5.70 131.60 143.00 +
P135 5.70 134.60 146.00 +
P140 5.70 139.60 151.00 +
P145 5.70 144.60 156.00 +
P150 5.70 149.60 161.00 +
P150A 8.40 149.50 166.30 +
P155 8.40 154.50 171.30 +
P160 8.40 159.50 176.30 +
P165 8.40 164.50 181.30 +
P170 8.40 169.50 186.30 +
P175 8.40 174.50 191.30 +
P180 8.40 179.50 196.30 +
P185 8.40 184.50 201.30 +
P190 8.40 189.50 206.30 +
P195 8.40 194.50 211.30 +
P200 8.40 199.50 216.30 +
P205 8.40 204.50 221.30 +
P209 8.40 208.50 225.30 +
P210 8.40 209.50 226.30 +
P215 8.40 214.50 231.30 +
P220 8.40 219.50 236.30 +
P225 8.40 224.50 241.30 +
P230 8.40 229.50 246.30 +
P235 8.40 234.50 251.30 +
P240 8.40 239.50 256.30 +
P245 8.40 244.50 261.30 +
P250 8.40 249.50 266.30 +
P255 8.40 254.50 271.30 +
P260 8.40 259.50 276.30 +
P265 8.40 264.50 281.30 +
P270 8.40 269.50 286.30 +
P275 8.40 274.50 291.30 +
P280 8.40 279.50 296.30 +
P285 8.40 284.50 301.30 +
P290 8.40 289.50 306.30 +
P295 8.40 294.50 311.30 +
P300 8.40 299.50 316.30 +
P305 8.40 304.50 321.30 +
P310 8.40 309.50 326.30 +
P315 8.40 314.50 331.30 +
P320 8.40 319.50 336.30 +
P325 8.40 324.50 341.30 +
P330 8.40 329.50 346.30 +
P335 8.40 334.50 351.30 +
P340 8.40 339.50 356.30 +
P345 8.40 344.50 361.30 +
P350 8.40 349.50 366.30 +
P355 8.40 354.50 371.30 +
P360 8.40 359.50 376.30 +
P365 8.40 364.50 381.30 +
P370 8.40 369.50 386.30 +
P375 8.40 374.50 391.30 +
P380 8.40 379.50 396.30 +
P385 8.40 384.50 401.30 +
P390 8.40 389.50 406.30 +
P395 8.40 394.50 411.30 +
P400 8.40 399.50 416.30 +
P405 8.40 404.50 421.30 +
P410 8.40 409.50 426.30 +
P415 8.40 414.50 431.30 +
P420 8.40 419.50 436.30 +
P425 8.40 424.50 441.30 +
P430 8.40 429.50 446.30 +
P435 8.40 434.50 451.30 +
P440 8.40 439.50 456.30 +
P445 8.40 444.50 461.30 +
P450 8.40 449.50 466.30 +
P455 8.40 454.50 471.30 +
P460 8.40 459.50 476.30 +
P465 8.40 464.50 481.30 +
P470 8.40 469.50 486.30 +
P475 8.40 474.50 491.30 +
P480 8.40 479.50 496.30 +
P485 8.40 484.50 501.30 +
P490 8.40 489.50 506.30 +
P495 8.40 494.50 511.30 +
P500 8.40 499.50 516.30 +
G25 3.10 24.40 30.60 +
G30 3.10 29.40 35.60 +
G35 3.10 34.40 40.60 +
G40 3.10 39.40 45.60 +
G45 3.10 44.40 50.60 +
G50 3.10 49.40 55.60 +
G55 3.10 54.40 60.60 +
G60 3.10 59.40 65.60 +
G65 3.10 64.40 70.60 +
G70 3.10 69.40 75.60 +
G75 3.10 74.40 80.60 +
G80 3.10 79.40 85.60 +
G85 3.10 84.40 90.60 +
G90 3.10 89.40 95.60 +
G95 3.10 94.40 100.60 +
G100 3.10 99.40 105.60 +
G105 3.10 104.40 110.60 +
G110 3.10 109.40 115.60 +
G115 3.10 114.40 120.60 +
G120 3.10 119.40 125.60 +
G125 3.10 124.40 130.60 +
G130 3.10 129.40 135.60 +
G135 3.10 134.40 140.60 +
G140 3.10 139.40 145.60 +
G145 3.10 144.40 150.60 +
G150 5.70 149.30 160.70 +
G155 5.70 154.30 165.70 +
G160 5.70 159.30 170.70 +
G165 5.70 164.30 175.70 +
G170 5.70 169.30 180.70 +
G175 5.70 174.30 185.70 +
G180 5.70 179.30 190.70 +
G185 5.70 184.30 195.70 +
G190 5.70 189.30 200.70 +
G195 5.70 194.30 205.70 +
G200 5.70 199.30 210.70 +
G210 5.70 209.30 220.70 +
G220 5.70 219.30 230.70 +
G230 5.70 229.30 240.70 +
G240 5.70 239.30 250.70 +
G250 5.70 249.30 260.70 +
G255 5.70 254.30 265.70 +
G260 5.70 259.30 270.70 +
G270 5.70 269.30 280.70 +
G280 5.70 279.30 290.70 +
G290 5.70 289.30 300.70 +
G300 5.70 299.30 310.70 +
G305 5.70 304.30 315.70 +
G310 5.70 309.30 320.70 +
G315 5.70 314.30 325.70 +
G320 5.70 319.30 330.70 +
G325 5.70 324.30 335.70 +
G330 5.70 329.30 340.70 +
G335 5.70 334.30 345.70 +
G340 5.70 339.30 350.70 +
G345 5.70 344.30 355.70 +
G350 5.70 349.30 360.70 +
G355 5.70 354.30 365.70 +
G360 5.70 359.30 370.70 +
G365 5.70 364.30 375.70 +
G370 5.70 369.30 380.70 +
G375 5.70 374.30 385.70 +
G380 5.70 379.30 390.70 +
G385 5.70 384.30 395.70 +
G390 5.70 389.30 400.70 +
G395 5.70 394.30 405.70 +
G400 5.70 399.30 410.70 +
G405 5.70 404.30 415.70 +
G410 5.70 409.30 420.70 +
G415 5.70 414.30 425.70 +
G420 5.70 419.30 430.70 +
G425 5.70 424.30 435.70 +
G430 5.70 429.30 440.70 +
G435 5.70 434.30 445.70 +
G440 5.70 439.30 450.70 +
G445 5.70 444.30 455.70 +
G450 5.70 449.30 460.70 +
G455 5.70 454.30 465.70 +
G460 5.70 459.30 470.70 +
G465 5.70 464.30 475.70 +
G470 5.70 469.30 480.70 +
G475 5.70 474.30 485.70 +
G480 5.70 479.30 490.70 +
G485 5.70 484.30 495.70 +
G490 5.70 489.30 500.70 +
G495 5.70 494.30 505.70 +
G500 5.70 499.30 510.70 +
S3 1.50 2.50 5.50 +
S4 1.50 3.50 6.50 +
S5 1.50 4.50 7.50 +
S6 1.50 5.50 8.50 +
S7 1.50 6.50 9.50 +
S8 1.50 7.50 10.50 +
S9 1.50 8.50 11.50 +
S10 1.50 9.50 12.50 +
S11.2 1.50 10.70 13.70 +
S12 1.50 11.50 14.50 +
S12.5 1.50 12.00 15.00 +
S14 1.50 13.50 16.50 +
S15 1.50 14.50 17.50 +
S16 1.50 15.50 18.50 +
S18 1.50 17.50 20.50 +
S20 1.50 19.50 22.50 +
S22 1.50 21.50 24.50 +
S22.4 2.00 21.90 25.90 +
S24 2.00 23.50 27.50 +
S25 2.00 24.50 28.50 +
S26 2.00 25.50 29.50 +
S28 2.00 27.50 31.50 +
S29 2.00 28.50 32.50 +
S30 2.00 29.50 33.50 +
S31.5 2.00 31.00 35.00 +
S32 2.00 31.50 35.50 +
S34 2.00 33.50 37.50 +
S35 2.00 34.50 38.50 +
S35.5 2.00 35.00 39.00 +
S36 2.00 35.50 39.50 +
S38 2.00 37.50 41.50 +
S39 2.00 38.50 42.50 +
S40 2.00 39.50 43.50 +
S42 2.00 41.50 45.50 +
S44 2.00 43.50 47.50 +
S45 2.00 44.50 48.50 +
S46 2.00 45.50 49.50 +
S48 2.00 47.50 51.50 +
S50 2.00 49.50 53.50 +
S53 2.00 52.50 56.50 +
S55 2.00 54.50 58.50 +
S56 2.00 55.50 59.50 +
S60 2.00 59.50 63.50 +
S63 2.00 62.50 66.50 +
S65 2.00 64.50 68.50 +
S67 2.00 66.50 70.50 +
S70 2.00 69.50 73.50 +
S71 2.00 70.50 74.50 +
S75 2.00 74.50 78.50 +
S80 2.00 79.50 83.50 +
S85 2.00 84.50 88.50 +
S90 2.00 89.50 93.50 +
S95 2.00 94.50 98.50 +
S100 2.00 99.50 103.50 +
S105 2.00 104.50 108.50 +
S110 2.00 109.50 113.50 +
S112 2.00 111.50 115.50 +
S115 2.00 114.50 118.50 +
S120 2.00 119.50 123.50 +
S125 2.00 124.50 128.50 +
S130 2.00 129.50 133.50 +
S132 2.00 131.50 135.50 +
S135 2.00 134.50 138.50 +
S140 2.00 139.50 143.50 +
S145 2.00 144.50 148.50 +
S150 2.00 149.50 153.50 +
SS005 1.00 0.50 2.50 +
SS008 1.00 0.80 2.80 +
SS010 1.00 1.00 3.00 +
SS012 1.00 1.20 3.20 +
SS015 1.00 1.50 3.50 +
SS020 1.00 2.00 4.00 +
SS022 1.00 2.20 4.20 +
SS025 1.00 2.50 4.50 +
SS028 1.00 2.80 4.80 +
SS030 1.00 3.00 5.00 +
SS032 1.00 3.20 5.20 +
SS035 1.00 3.50 5.50 +
SS038 1.00 3.80 5.80 +
SS040 1.00 4.00 6.00 +
SS042 1.00 4.20 6.20 +
SS045 1.00 4.50 6.50 +
SS048 1.00 4.80 6.80 +
SS050 1.00 5.00 7.00 +
SS055 1.00 5.50 7.50 +
SS060 1.00 6.00 8.00 +
SS065 1.00 6.50 8.50 +
SS070 1.00 7.00 9.00 +
SS075 1.00 7.50 9.50 +
SS080 1.00 8.00 10.00 +
SS085 1.00 8.50 10.50 +
SS090 1.00 9.00 11.00 +
SS095 1.00 9.50 11.50 +
SS100 1.00 10.00 12.00 +
SS105 1.00 10.50 12.50 +
SS110 1.00 11.00 13.00 +
SS115 1.00 11.50 13.50 +
SS120 1.00 12.00 14.00 +
SS125 1.00 12.50 14.50 +
SS130 1.00 13.00 15.00 +
SS135 1.00 13.50 15.50 +
SS140 1.00 14.00 16.00 +
SS145 1.00 14.50 16.50 +
SS150 1.00 15.00 17.00 +
SS155 1.00 15.50 17.50 +
SS160 1.00 16.00 18.00 +
SS165 1.00 16.50 18.50 +
SS170 1.00 17.00 19.00 +
SS175 1.00 17.50 19.50 +
SS180 1.00 18.00 20.00 +
SS185 1.00 18.50 20.50 +
SS190 1.00 19.00 21.00 +
SS195 1.00 19.50 21.50 +
SS200 1.00 20.00 22.00 +
V15 4.00 14.50 22.50 +
V24 4.00 23.50 31.50 +
V34 4.00 33.50 41.50 +
V40 4.00 39.50 47.50 +
V55 4.00 54.50 62.50 +
V70 4.00 69.00 77.00 +
V85 4.00 84.00 92.00 +
V100 4.00 99.00 107.00 +
V120 4.00 119.00 127.00 +
V150 4.00 148.50 156.50 +

Use + at the end of a row to keep that size. The list follows you to the other charts. Material and quantity can be set per size in the tray, and the enquiry form opens with those lines ready.

The same two ways in as the AS568 chart: type the code if you have one, or enter the inside diameter and cross section and compare with the closest JIS sizes.

Interactive Lookup

P, G, S, SS and V codes. Type the code with or without the series letter spacing, for example P22, p22 or SS100.

By size code

For example P22 or G45.



By measured dimensions

The five closest JIS sizes are listed with the difference in inside diameter.





If you are cutting a new groove rather than matching a size that already exists, the groove design page carries the gland depth and groove width bands for the inch cross sections; JIS sections differ, and for those we work from your drawing, plus a checker that turns a measured groove into squeeze and fill.

Tolerances And Acceptance

JIS B 2401 does not carry one tolerance for the whole list. The cord tolerance is fixed by the series and the inside diameter tolerance is banded by size, so the band has to be read with the code rather than assumed from it.

Cord Tolerance By Series

Series Cord (mm) Cord tolerance
P 1.90 ±0.08
P 2.40 ±0.09
P 3.50 ±0.10
P 5.70 ±0.13
P 8.40 ±0.15
G 3.10 ±0.10
G 5.70 ±0.13
V 4.00 ±0.10

The S and SS series use thinner cords, 2.00, 1.50 and 1.00 mm. Their bands come from the same table in the standard and are printed with the quotation rather than guessed from the cord.

The Inside Diameter Band Grows With The Size

The inside diameter band is not one figure for the list. A P22 at 21.80 mm is held to plus or minus 0.24 mm, and a P125 at 124.60 mm to plus or minus 1.01 mm. On the large sizes the band is a full millimetre either side, which is more than the difference a bench measurement can resolve on a soft ring, so the code and the measurement have to travel together.

This is where a Japanese drawing and a Japanese spare part most often part company. The code fixes the nominal size, the band fixes what a new ring may measure, and a used ring that has taken a set will sit below both. Measure a new ring where you can, and put the series letter on the enquiry even when the dimensions are known.

What We Accept At Inspection

What is checked What we hold Where it is written
Inside diameter and cross section The band the standard prints for that size, not the nominal figure Quotation and inspection sheet
Surface and visual defects The grade named on the drawing. Where the drawing is silent we work to ISO 3601-3 grade N Quotation, and the sample you approve
Hardness ±5 Shore A around the nominal figure Test certificate
Compound and cure The compound quoted, batch traceable Certificate of conformity on request
Tolerance tighter than the standard Quoted case by case, because it is a moulding capability question and not a paperwork one Drawing and agreed deviation

When A Ring Measures Outside

Every production lot is sampled against the band before it is packed. A lot that falls outside is held, and you hear it from us before it ships. The options are a remake, shipment against a written deviation you have accepted, or a credit. Shipping it and letting the difference turn up at your incoming inspection is not one of them.

Dimensions are checked on rings that have lain free and unstressed for at least an hour at 23 °C and 50 % relative humidity, as ISO 23529 sets out. Inside diameter is read with a taper gauge or a calibrated plug, cross section with a micrometer at light closing pressure. A ring measured while stretched, or straight off a warm press, will not agree with the band it was made to.

The bands on this page are the ones we work to in normal production. Where this page and the text of the standard disagree, the standard text governs, and where your drawing is tighter than the standard, the drawing governs.

Where JIS Does Not Convert

The Japanese series were built around metric cords of 1.50, 1.90, 2.00, 2.40, 3.50, 5.70 and 8.40 mm, and several of those do not exist in the inch standards at all. A 3.50 mm cord sits between the AS568 2.62 and 3.53 mm cords, closer to the metric ISO 3601 group C at 3.55 mm. There is no dash number or ISO code that is the same ring.

Two conversions do hold. A JIS size with a 3.55 mm cord can often be met from ISO 3601 Class B, and a JIS size with a 3.53 mm cord can often be met from the inch list on the AS568 chart. Both are applications of the nearest size rather than a standard conversion, so check the groove before you switch. The O-ring standard cross reference has worked examples of pairs that look equivalent and are not.

What To Send With An Enquiry

  • The full code, for example JIS B 2401 P22, including the series letter
  • Inside diameter and cross section in millimetres, if the drawing gives them
  • Compound and hardness, and whether the ring runs dynamic or static
  • Quantity per size and per year
  • The drawing, where the tolerance is tighter than the standard or the size is not in the chart

Request a Quote

Questions We Get Asked

Why is P22 not 22 mm?
The number in a JIS code is nominal. P22 measures 21.80 mm inside diameter with a 2.40 mm cross section. The offset comes from the series, not from the individual size, so neighbouring codes are offset by the same amount.

Is a JIS P ring the same as an ISO 3601 Class B ring?
Not by code, and not always by size. A P ring with a 3.50 mm cord has no Class B equivalent, because the Class B groups run 1.80, 2.65, 3.55, 5.30 and 7.00 mm. Where a P size lands on 3.55 mm, the Class B ring is usually the practical substitute, subject to the groove.

Do you make the SS and V series?
Yes. Both are moulded to the sizes in the chart, and the V series is available in the same compounds as the P series. Sizes above the ranges shown are quoted individually.

Can I mix series on one machine?
Only where the groove is cut for that cord. The series are chosen for the joint, not for the size, so replacing a G ring with a P ring of the same inside diameter changes the squeeze and the contact width.

滚动至顶部