Nitrile is the compound most O-rings are made from, and for good reason: it handles mineral oil, grease and hydraulic fluid at a price that lets a buyer stock three sizes instead of one. If the application is a gearbox, a pump, a cylinder or a machine tool, NBR is the first material to consider and usually the last one chosen.
It is also the compound that fails most predictably. Nitrile has no answer to ozone, to sunlight, or to the ketones and esters that appear in paint and adhesive lines, and it hardens rather than softens when it finally goes. This page sets out where the boundary is, so a switch to EPDM or FKM happens before a leak rather than after it.
What NBR Is
NBR is a copolymer of butadiene and acrylonitrile. The acrylonitrile content is the dial that matters: more of it gives better resistance to oil and fuel and a higher glass transition temperature, so a 34 percent bound acrylonitrile compound holds oil better than a 28 percent one and stops being flexible about 10 °C sooner. That trade is why two NBR O-rings that look identical can behave differently in the same groove, and why we ask for the medium and the lowest start-up temperature before quoting a grade.
Properties At A Glance
The figures below are typical for a 70 Shore A compound of this class, which is the hardness most of our stock and most drawings call for. A 90 Shore A version of the same polymer will sit at the top of the hardness range and at the bottom of the temperature range.
| Property | Typical value | What it means |
|---|---|---|
| Hardness | 40 to 90 Shore A | 70 is standard; 90 for high pressure, 50 for light covers |
| Temperature range | −40 to +100 °C | Short excursions to 120 °C; low temperature grades to −50 °C |
| Colour | Black | Not a specification; green and blue are the usual markers |
| Tensile strength | 10 to 17 MPa | Falls by about a third at 100 °C |
| Compression set | Good | Better than silicone, worse than FKM at the same temperature |
| Gas permeability | Low | The reason nitrile is used in vacuum and gas service |
| Relative cost | Low | The cheapest of the five compounds on the matrix |
Where It Works
- Mineral oil, hydraulic oil, diesel, grease and most gear lubricants
- Air, water and water glycol at moderate temperature
- Vacuum and gas service, where its low permeability matters more than its heat limit
- Dynamic duty in pumps and cylinders, because it has the tear strength silicone lacks
- General industrial spares, where a stocked size has to cover several machines
Where It Fails
- Ozone, sunlight and weathering: cracking starts at the surface and goes through
- Ketones, esters and strong solvents, including acetone, MEK and many paint lines
- High aromatic fuels and aromatic process oils, which swell it badly
- Steam above about 100 °C and hot water over long exposure
- Brake fluid and phosphate esters, which are the classic nitrile failure in workshops
Resistance To Common Media
Ratings are for the compound class at room temperature unless the note says otherwise, and they describe swelling, hardening and loss of strength together rather than one figure. A compound that swells 20 percent has already changed its squeeze.
| Medium | Rating | In practice |
|---|---|---|
| Mineral and hydraulic oil | Excellent | Standard duty, the reason NBR is the default |
| Diesel and kerosene | Good | High acrylonitrile grades hold better; check volume swell |
| Petrol with high aromatic content | Fair | Swells; FKM is the safer answer |
| Water and water glycol | Good | Up to about 80 °C for long service |
| Steam | Poor | Hardens and loses elasticity quickly |
| Dilute acids and bases | Fair | Depends on concentration; test where the duty is continuous |
| Ketones, esters, brake fluid | Poor | Swelling within days |
| Ozone and weather | Poor | Add waxes or switch compound; do not leave NBR outdoors |
Compounds We Quote
We quote NBR from 40 to 90 Shore A in sulphur cured and peroxide cured versions. Sulphur cured is the general purpose compound and the cheaper one; peroxide cured holds compression set better at 100 °C and is preferred where the joint is hot and static. Food contact grades to FDA 21 CFR 177.2600 and drinking water grades to WRAS are available on request with the certificate, and a white or blue compound can be supplied where colour coding matters.
If the drawing carries an ASTM D2000 line callout, the callout governs rather than this page. Our guide to {link(‘astm-d2000-line-callout-guide’, ‘reading a D2000 line callout’)} explains how the suffix tests translate into what we report on the certificate.
Sizes And Standards
Choosing between compounds rather than specifying one? The O-ring material comparison puts all five side by side at 70 Shore A, with the temperature range and the media each one cannot take.
The size is a separate decision from the compound, and it is the one buyers most often get wrong. The four standard lists are on their own pages, each with a lookup that takes either the code or a pair of measured dimensions: AS568 (inch dash numbers), ISO 3601 (Class A and Class B metric), JIS B 2401 (P, G, S, SS and V series) and BS 1806 (British imperial numbers). If the drawing gives a size outside those lists, or a cord that is not standard, we mould to drawing.
What To Send With An Enquiry
- The size or dash number, and the standard it comes from
- The medium, with the concentration if it is an acid, base or solvent blend
- The working temperature range, including start-up and any cleaning cycle
- Hardness, and whether the seal is static or dynamic
- Any approval needed: FDA, WRAS, or a D2000 callout with its suffix tests
What is the maximum temperature for NBR O-rings?
About 100 °C in continuous service, with short excursions to 120 °C. The limit is not a softening point but an oxidation one: above 100 °C the compound hardens and takes a permanent set, so a ring that still looks sound will leak after a few heat cycles.
Will NBR seal brake fluid?
No. Glycol brake fluid and phosphate ester hydraulic fluid swell and soften nitrile. EPDM is the usual answer for glycol brake fluid, and for phosphate esters the choice is butyl or a dedicated compound, so send the fluid name rather than the application.
Can I use NBR outdoors?
Only behind a cover. Ozone and ultraviolet light crack nitrile, and the cracks run through the section rather than staying on the surface. EPDM or neoprene is the outdoor choice at similar cost.
Is NBR the same as Buna-N?
Yes. Buna-N, nitrile, NBR and acrylonitrile butadiene rubber all name the same polymer, and an American drawing may use any of the four.
