ISO 3601 O-Ring Size Chart: Class B Codes and Metric Sizes

ISO 3601-1 is the international O-ring standard, and it carries two size lists that behave nothing alike. Class A is the American inch list published under an ISO cover. Class B is a metric list with its own inside diameters and its own groups of cross section. A drawing that says ISO 3601 without naming the class has not told you which ring it wants.

We make both classes. This page explains how a Class B code is built, lists the metric sizes with inside diameter and cross section, and adds a lookup that works from either the code or the dimensions you measured.

The Two Classes In One Standard

The names suggest two tolerance grades of the same list. They are not. Class A repeats AS568 dash numbers size for size, so a 214 to Class A is the same part as an AS568 -214. Class B is a separate metric list, and its cords are close to but not the same as the inch cords it sits beside.

Class Sizes Cords How a size is written Where the list comes from
Class A AS568 inch sizes 1.02 to 6.99 mm Dash number, for example 214 The AS568 list, repeated with the same tolerances
Class B Metric sizes 1.80, 2.65, 3.55, 5.30 and 7.00 mm Group letter plus four digits, for example C0250 ISO 3601 own metric list

Because the two lists are close, a Class A ring often looks like it will do a Class B job. The cord is the tell: 1.78 mm against 1.80 mm, or 2.62 mm against 2.65 mm. Twenty to thirty microns of extra cord is a different squeeze in a groove that was cut for the metric size, so we quote the class on the drawing and on the bag.

How A Class B Code Is Built

Take C0250. The letter gives the group, and the group fixes the cross section, so the cord is not written anywhere in the code. The four digits are the inside diameter in tenths of a millimetre: 0250 is 25.0 mm. The outside diameter is not in the code at all, and it is simply the inside diameter plus twice the cord, which comes to 32.10 mm for this ring.

Group Cord (mm) Cord tolerance Inside diameters covered In the table below
A 1.80 ±0.08 1.8 to 125.0 78
B 2.65 ±0.09 4.5 to 250.0 82
C 3.55 ±0.10 14.0 to 355.0 100
D 5.30 ±0.13 37.5 to 200.0 decoded
E 7.00 ±0.15 109.0 to 400.0 decoded

Groups D and E are shorter lists and follow the same rule, so the lookup decodes them directly: the digits are the inside diameter in tenths of a millimetre and the letter supplies 5.30 mm or 7.00 mm of cord. If you need a D or E size that is not in the table, the lookup still gives you the dimensions to quote.

ISO 3601 Class B Size Chart

Inside diameter and cross section are the two dimensions a groove is cut to, so both are given in millimetres, with the resulting outside diameter alongside. The filter row under the headings searches each column, so typing 3.55 in the cross section column narrows the list to group C.

ISO 3601 code CS (mm) ID (mm) OD (mm) Quote
A0018 1.80 1.80 5.40 +
A0020 1.80 2.00 5.60 +
A0022 1.80 2.24 5.84 +
A0025 1.80 2.50 6.10 +
A0028 1.80 2.80 6.40 +
A0032 1.80 3.15 6.75 +
A0036 1.80 3.55 7.15 +
A0038 1.80 3.75 7.35 +
A0040 1.80 4.00 7.60 +
A0045 1.80 4.50 8.10 +
A0049 1.80 4.87 8.47 +
A0050 1.80 5.00 8.60 +
A0052 1.80 5.15 8.75 +
A0053 1.80 5.30 8.90 +
A0056 1.80 5.60 9.20 +
A0060 1.80 6.00 9.60 +
A0063 1.80 6.30 9.90 +
A0067 1.80 6.70 10.30 +
A0069 1.80 6.90 10.50 +
A0071 1.80 7.10 10.70 +
A0075 1.80 7.50 11.10 +
A0080 1.80 8.00 11.60 +
A0085 1.80 8.50 12.10 +
A0088 1.80 8.75 12.35 +
A0090 1.80 9.00 12.60 +
A0095 1.80 9.50 13.10 +
A0100 1.80 10.00 13.60 +
A0106 1.80 10.60 14.20 +
A0112 1.80 11.20 14.80 +
A0118 1.80 11.80 15.40 +
A0125 1.80 12.50 16.10 +
A0132 1.80 13.20 16.80 +
A0140 1.80 14.00 17.60 +
A0150 1.80 15.00 18.60 +
A0160 1.80 16.00 19.60 +
A0170 1.80 17.00 20.60 +
A0180 1.80 18.00 21.60 +
A0190 1.80 19.00 22.60 +
A0200 1.80 20.00 23.60 +
A0212 1.80 21.20 24.80 +
A0224 1.80 22.40 26.00 +
A0236 1.80 23.60 27.20 +
A0250 1.80 25.00 28.60 +
A0258 1.80 25.80 29.40 +
A0265 1.80 26.50 30.10 +
A0280 1.80 28.00 31.60 +
A0300 1.80 30.00 33.60 +
A0315 1.80 31.50 35.10 +
A0325 1.80 32.50 36.10 +
A0335 1.80 33.50 37.10 +
A0345 1.80 34.50 38.10 +
A0355 1.80 35.50 39.10 +
A0365 1.80 36.50 40.10 +
A0375 1.80 37.50 41.10 +
A0387 1.80 38.70 42.30 +
A0400 1.80 40.00 43.60 +
A0412 1.80 41.20 44.80 +
A0425 1.80 42.50 46.10 +
A0437 1.80 43.70 47.30 +
A0450 1.80 45.00 48.60 +
A0475 1.80 47.50 51.10 +
A0500 1.80 50.00 53.60 +
A0530 1.80 53.00 56.60 +
A0560 1.80 56.00 59.60 +
A0600 1.80 60.00 63.60 +
A0630 1.80 63.00 66.60 +
A0670 1.80 67.00 70.60 +
A0710 1.80 71.00 74.60 +
A0750 1.80 75.00 78.60 +
A0800 1.80 80.00 83.60 +
A0850 1.80 85.00 88.60 +
A0900 1.80 90.00 93.60 +
A0950 1.80 95.00 98.60 +
A1000 1.80 100.00 103.60 +
A1060 1.80 106.00 109.60 +
A1120 1.80 112.00 115.60 +
A1180 1.80 118.00 121.60 +
A1250 1.80 125.00 128.60 +
B0045 2.65 4.50 9.80 +
B0053 2.65 5.30 10.60 +
B0060 2.65 6.00 11.30 +
B0069 2.65 6.90 12.20 +
B0080 2.65 8.00 13.30 +
B0090 2.65 9.00 14.30 +
B0095 2.65 9.50 14.80 +
B0100 2.65 10.00 15.30 +
B0106 2.65 10.60 15.90 +
B0112 2.65 11.20 16.50 +
B0118 2.65 11.80 17.10 +
B0125 2.65 12.50 17.80 +
B0132 2.65 13.20 18.50 +
B0140 2.65 14.00 19.30 +
B0150 2.65 15.00 20.30 +
B0160 2.65 16.00 21.30 +
B0170 2.65 17.00 22.30 +
B0180 2.65 18.00 23.30 +
B0190 2.65 19.00 24.30 +
B0200 2.65 20.00 25.30 +
B0212 2.65 21.20 26.50 +
B0224 2.65 22.40 27.70 +
B0236 2.65 23.60 28.90 +
B0250 2.65 25.00 30.30 +
B0258 2.65 25.80 31.10 +
B0265 2.65 26.50 31.80 +
B0280 2.65 28.00 33.30 +
B0300 2.65 30.00 35.30 +
B0315 2.65 31.50 36.80 +
B0325 2.65 32.50 37.80 +
B0335 2.65 33.50 38.80 +
B0345 2.65 34.50 39.80 +
B0355 2.65 35.50 40.80 +
B0365 2.65 36.50 41.80 +
B0375 2.65 37.50 42.80 +
B0387 2.65 38.70 44.00 +
B0400 2.65 40.00 45.30 +
B0412 2.65 41.20 46.50 +
B0425 2.65 42.50 47.80 +
B0437 2.65 43.70 49.00 +
B0450 2.65 45.00 50.30 +
B0462 2.65 46.20 51.50 +
B0475 2.65 47.50 52.80 +
B0487 2.65 48.70 54.00 +
B0500 2.65 50.00 55.30 +
B0515 2.65 51.50 56.80 +
B0530 2.65 53.00 58.30 +
B0545 2.65 54.50 59.80 +
B0560 2.65 56.00 61.30 +
B0580 2.65 58.00 63.30 +
B0600 2.65 60.00 65.30 +
B0615 2.65 61.50 66.80 +
B0630 2.65 63.00 68.30 +
B0650 2.65 65.00 70.30 +
B0670 2.65 67.00 72.30 +
B0690 2.65 69.00 74.30 +
B0710 2.65 71.00 76.30 +
B0730 2.65 73.00 78.30 +
B0750 2.65 75.00 80.30 +
B0800 2.65 80.00 85.30 +
B0850 2.65 85.00 90.30 +
B0900 2.65 90.00 95.30 +
B0950 2.65 95.00 100.30 +
B1000 2.65 100.00 105.30 +
B1060 2.65 106.00 111.30 +
B1120 2.65 112.00 117.30 +
B1180 2.65 118.00 123.30 +
B1250 2.65 125.00 130.30 +
B1320 2.65 132.00 137.30 +
B1400 2.65 140.00 145.30 +
B1500 2.65 150.00 155.30 +
B1600 2.65 160.00 165.30 +
B1700 2.65 170.00 175.30 +
B1800 2.65 180.00 185.30 +
B1900 2.65 190.00 195.30 +
B2000 2.65 200.00 205.30 +
B2120 2.65 212.00 217.30 +
B2240 2.65 224.00 229.30 +
B2300 2.65 230.00 235.30 +
B2360 2.65 236.00 241.30 +
B2430 2.65 243.00 248.30 +
B2500 2.65 250.00 255.30 +
C0140 3.55 14.00 21.10 +
C0145 3.55 14.50 21.60 +
C0150 3.55 15.00 22.10 +
C0155 3.55 15.50 22.60 +
C0160 3.55 16.00 23.10 +
C0170 3.55 17.00 24.10 +
C0180 3.55 18.00 25.10 +
C0190 3.55 19.00 26.10 +
C0200 3.55 20.00 27.10 +
C0206 3.55 20.60 27.70 +
C0212 3.55 21.20 28.30 +
C0224 3.55 22.40 29.50 +
C0236 3.55 23.60 30.70 +
C0243 3.55 24.30 31.40 +
C0250 3.55 25.00 32.10 +
C0258 3.55 25.80 32.90 +
C0265 3.55 26.50 33.60 +
C0273 3.55 27.30 34.40 +
C0280 3.55 28.00 35.10 +
C0300 3.55 30.00 37.10 +
C0315 3.55 31.50 38.60 +
C0325 3.55 32.50 39.60 +
C0335 3.55 33.50 40.60 +
C0345 3.55 34.50 41.60 +
C0355 3.55 35.50 42.60 +
C0365 3.55 36.50 43.60 +
C0375 3.55 37.50 44.60 +
C0387 3.55 38.70 45.80 +
C0400 3.55 40.00 47.10 +
C0412 3.55 41.20 48.30 +
C0425 3.55 42.50 49.60 +
C0437 3.55 43.70 50.80 +
C0450 3.55 45.00 52.10 +
C0462 3.55 46.20 53.30 +
C0475 3.55 47.50 54.60 +
C0487 3.55 48.70 55.80 +
C0500 3.55 50.00 57.10 +
C0515 3.55 51.50 58.60 +
C0530 3.55 53.00 60.10 +
C0545 3.55 54.50 61.60 +
C0560 3.55 56.00 63.10 +
C0580 3.55 58.00 65.10 +
C0600 3.55 60.00 67.10 +
C0615 3.55 61.50 68.60 +
C0630 3.55 63.00 70.10 +
C0650 3.55 65.00 72.10 +
C0670 3.55 67.00 74.10 +
C0690 3.55 69.00 76.10 +
C0710 3.55 71.00 78.10 +
C0730 3.55 73.00 80.10 +
C0750 3.55 75.00 82.10 +
C0775 3.55 77.50 84.60 +
C0800 3.55 80.00 87.10 +
C0825 3.55 82.50 89.60 +
C0850 3.55 85.00 92.10 +
C0875 3.55 87.50 94.60 +
C0900 3.55 90.00 97.10 +
C0925 3.55 92.50 99.60 +
C0950 3.55 95.00 102.10 +
C0975 3.55 97.50 104.60 +
C1000 3.55 100.00 107.10 +
C1030 3.55 103.00 110.10 +
C1060 3.55 106.00 113.10 +
C1090 3.55 109.00 116.10 +
C1120 3.55 112.00 119.10 +
C1150 3.55 115.00 122.10 +
C1180 3.55 118.00 125.10 +
C1220 3.55 122.00 129.10 +
C1250 3.55 125.00 132.10 +
C1280 3.55 128.00 135.10 +
C1320 3.55 132.00 139.10 +
C1360 3.55 136.00 143.10 +
C1400 3.55 140.00 147.10 +
C1450 3.55 145.00 152.10 +
C1500 3.55 150.00 157.10 +
C1550 3.55 155.00 162.10 +
C1600 3.55 160.00 167.10 +
C1650 3.55 165.00 172.10 +
C1700 3.55 170.00 177.10 +
C1750 3.55 175.00 182.10 +
C1800 3.55 180.00 187.10 +
C1850 3.55 185.00 192.10 +
C1900 3.55 190.00 197.10 +
C1950 3.55 195.00 202.10 +
C2000 3.55 200.00 207.10 +
C2120 3.55 212.00 219.10 +
C2180 3.55 218.00 225.10 +
C2240 3.55 224.00 231.10 +
C2300 3.55 230.00 237.10 +
C2360 3.55 236.00 243.10 +
C2500 3.55 250.00 257.10 +
C2580 3.55 258.00 265.10 +
C2650 3.55 265.00 272.10 +
C2800 3.55 280.00 287.10 +
C2900 3.55 290.00 297.10 +
C3000 3.55 300.00 307.10 +
C3070 3.55 307.00 314.10 +
C3150 3.55 315.00 322.10 +
C3350 3.55 335.00 342.10 +
C3550 3.55 355.00 362.10 +

Use + at the end of a row to keep that size. The list follows you to the other charts. Material and quantity can be set per size in the tray, and the enquiry form opens with those lines ready.

The lookup below works the same way as the one on the AS568 chart, and it also decodes any D or E group code that is not in the table.

Interactive Lookup

Class B sizes from the table below, plus any D or E group code, which is decoded from the digits and the group cord.

By size code

For example C0250, a0100 or E2500. Spaces and lower case are ignored.



By measured dimensions

The five closest Class B sizes are listed with the difference in inside diameter.





If you are cutting a new groove rather than matching a size that already exists, the groove design page carries the gland depth and groove width bands for the AS568 and ISO inch cross sections, plus a checker that turns a measured groove into squeeze and fill.

Tolerances And Acceptance

ISO 3601 answers two separate questions, and a drawing that names only the first has not described the part. ISO 3601-1 fixes the dimensional band on the size. ISO 3601-3 fixes what counts as an acceptable surface on the sealing face.

The Band On A Class B Ring

ISO 3601-1 sets the inside diameter tolerance from a formula rather than a table, which is why two suppliers can quote slightly different bands for the same size. The tolerance on the inside diameter is plus or minus 0.009 times the inside diameter to the power 0.95, plus 0.11 mm. On a 25 mm ring that works out at 0.30 mm, and on a 355 mm ring at 2.5 mm.

The cross section tolerance is fixed by the group and is listed with the groups above: 0.08 mm on 1.80 mm of cord, 0.09 on 2.65, 0.10 on 3.55, 0.13 on 5.30 and 0.15 on 7.00. The two bands are independent, so a ring can sit inside one and outside the other, and the groove feels the cross section first.

Surface Acceptance: ISO 3601-3

ISO 3601-3 grades the number and size of imperfections allowed on the sealing face, and it is the part of the standard that decides whether a ring measuring correctly is accepted. Grade N is the general purpose grade and the one we work to unless your drawing names another. A stricter grade is quoted with the surface criteria written out on the quotation, so nothing is left to interpret at incoming inspection.

What We Accept At Inspection

What is checked What we hold Where it is written
Inside diameter and cross section The band the standard prints for that size, not the nominal figure Quotation and inspection sheet
Surface and visual defects The grade named on the drawing. Where the drawing is silent we work to ISO 3601-3 grade N Quotation, and the sample you approve
Hardness ±5 Shore A around the nominal figure Test certificate
Compound and cure The compound quoted, batch traceable Certificate of conformity on request
Tolerance tighter than the standard Quoted case by case, because it is a moulding capability question and not a paperwork one Drawing and agreed deviation

When A Ring Measures Outside

Every production lot is sampled against the band before it is packed. A lot that falls outside is held, and you hear it from us before it ships. The options are a remake, shipment against a written deviation you have accepted, or a credit. Shipping it and letting the difference turn up at your incoming inspection is not one of them.

Dimensions are checked on rings that have lain free and unstressed for at least an hour at 23 °C and 50 % relative humidity, as ISO 23529 sets out. Inside diameter is read with a taper gauge or a calibrated plug, cross section with a micrometer at light closing pressure. A ring measured while stretched, or straight off a warm press, will not agree with the band it was made to.

The bands on this page are the ones we work to in normal production. Where this page and the text of the standard disagree, the standard text governs, and where your drawing is tighter than the standard, the drawing governs.

Class A Rings Are AS568 Rings

If the drawing says ISO 3601 Class A, the size list you need is the inch one. Every dash number with its inside diameter, cross section and tolerance is on the AS568 O-ring size chart, and the same lookup there takes a dash number or a pair of measured dimensions.

Converting Between The Systems

Where a drawing mixes an ISO code with an American or Japanese part number, the conversion is a decision rather than a lookup. The O-ring standard cross reference sets out how AS568, ISO 3601 Class A and B, JIS B 2401, BS 1806 and DIN 3771 identify a size, with worked examples of pairs that look interchangeable and are not.

What To Send With An Enquiry

  • The code with its class, for example ISO 3601 Class B C0250, so the cord is not left to interpretation
  • Inside diameter and cross section in millimetres, measured on a new ring if you have one
  • Compound and hardness, since the same size in NBR and FKM is a different part number for us
  • Quantity per size and per year, so the quotation reflects how the rings will be made
  • The drawing, if the size is not in the table or the tolerance is tighter than the standard

Quotations for standard Class B sizes are usually returned the same working day.

Request a Quote

Questions We Get Asked

Is ISO 3601 the same as AS568?
Only Class A. Class A repeats the AS568 inch list with the same dash numbers and tolerances. Class B is a separate metric list, and a Class B code such as C0250 has no dash number equivalent, though a 25 x 3.53 mm AS568 -214 is often used where the groove allows it.

What does the letter in C0250 mean?
It gives the cross section group. C is 3.55 mm of cord. The digits that follow are the inside diameter in tenths of a millimetre, so C0250 is 25.0 mm inside diameter and 32.10 mm outside diameter.

Can I use a 3.53 mm cord where the drawing says 3.55 mm?
Not as a like for like replacement. The groove was cut for a metric cord and the squeeze changes by about 0.6 percent, which matters on a dynamic seal and on a joint that already runs hot. Send the groove dimensions and we will tell you what the difference does in your application.

Do you supply the D and E groups?
Yes. Both are made to order in the same compounds as the A, B and C groups. The lookup above decodes a D or E code to its dimensions so you can quote it without waiting for a table.

滚动至顶部