The AS568 chart below is the complete standard inch series: 350 sizes, covering the dash numbers from -001 to -475 and the 001½ ring, with the inside diameter and cross section in inches and millimetres, the outside diameter, the inside diameter tolerance, and the series each number belongs to. All of it sits in one table that scrolls inside its own frame, with the header and a filter box under each column pinned in place. Type 214 in the dash column to go straight to that size, 21 to see the whole -21x block, or 3.5 in the ID (mm) column to list every ring with a 3.5 mm bore.
O.S Seals supplies these standard sizes in NBR, FKM, EPDM, HNBR, silicone and FFKM, with production at certified partner factories in China, and has non-standard sizes produced to drawing or sample. If a size you need is not on this chart, send the dimensions and we will quote it.
AS568 Size Chart: All 350 Sizes
The filter boxes take partial values, so two or three digits in the dash column are usually enough to reach a size. Clear a box to bring the full list back. The tolerance column is the permitted deviation on the inside diameter, not on the outside diameter.
| Dash no. | Series | ID (in) | ID (mm) | CS (in) | CS (mm) | OD (mm) | ID tol. (in) | Quote |
|---|---|---|---|---|---|---|---|---|
| -001 | 000 | 0.029 | 0.74 | 0.040 | 1.02 | 2.77 | ±0.004 | + |
| -001½ | 000 | 0.070 | 1.78 | 0.040 | 1.02 | 3.82 | ±0.005 | + |
| -002 | 000 | 0.042 | 1.07 | 0.050 | 1.27 | 3.61 | ±0.004 | + |
| -003 | 000 | 0.056 | 1.42 | 0.060 | 1.52 | 4.47 | ±0.004 | + |
| -004 | 000 | 0.070 | 1.78 | 0.070 | 1.78 | 5.33 | ±0.005 | + |
| -005 | 000 | 0.101 | 2.57 | 0.070 | 1.78 | 6.12 | ±0.005 | + |
| -006 | 000 | 0.114 | 2.90 | 0.070 | 1.78 | 6.45 | ±0.005 | + |
| -007 | 000 | 0.145 | 3.68 | 0.070 | 1.78 | 7.24 | ±0.005 | + |
| -008 | 000 | 0.176 | 4.47 | 0.070 | 1.78 | 8.03 | ±0.005 | + |
| -009 | 000 | 0.208 | 5.28 | 0.070 | 1.78 | 8.84 | ±0.005 | + |
| -010 | 000 | 0.239 | 6.07 | 0.070 | 1.78 | 9.63 | ±0.005 | + |
| -011 | 000 | 0.301 | 7.65 | 0.070 | 1.78 | 11.20 | ±0.005 | + |
| -012 | 000 | 0.364 | 9.25 | 0.070 | 1.78 | 12.80 | ±0.005 | + |
| -013 | 000 | 0.426 | 10.82 | 0.070 | 1.78 | 14.38 | ±0.005 | + |
| -014 | 000 | 0.489 | 12.42 | 0.070 | 1.78 | 15.98 | ±0.005 | + |
| -015 | 000 | 0.551 | 14.00 | 0.070 | 1.78 | 17.55 | ±0.007 | + |
| -016 | 000 | 0.614 | 15.60 | 0.070 | 1.78 | 19.15 | ±0.009 | + |
| -017 | 000 | 0.676 | 17.17 | 0.070 | 1.78 | 20.73 | ±0.009 | + |
| -018 | 000 | 0.739 | 18.77 | 0.070 | 1.78 | 22.33 | ±0.009 | + |
| -019 | 000 | 0.801 | 20.35 | 0.070 | 1.78 | 23.90 | ±0.009 | + |
| -020 | 000 | 0.864 | 21.95 | 0.070 | 1.78 | 25.50 | ±0.009 | + |
| -021 | 000 | 0.926 | 23.52 | 0.070 | 1.78 | 27.08 | ±0.009 | + |
| -022 | 000 | 0.989 | 25.12 | 0.070 | 1.78 | 28.68 | ±0.010 | + |
| -023 | 000 | 1.051 | 26.70 | 0.070 | 1.78 | 30.25 | ±0.010 | + |
| -024 | 000 | 1.114 | 28.30 | 0.070 | 1.78 | 31.85 | ±0.010 | + |
| -025 | 000 | 1.176 | 29.87 | 0.070 | 1.78 | 33.43 | ±0.011 | + |
| -026 | 000 | 1.239 | 31.47 | 0.070 | 1.78 | 35.03 | ±0.011 | + |
| -027 | 000 | 1.301 | 33.05 | 0.070 | 1.78 | 36.60 | ±0.011 | + |
| -028 | 000 | 1.364 | 34.65 | 0.070 | 1.78 | 38.20 | ±0.013 | + |
| -029 | 000 | 1.489 | 37.82 | 0.070 | 1.78 | 41.38 | ±0.013 | + |
| -030 | 000 | 1.614 | 41.00 | 0.070 | 1.78 | 44.55 | ±0.013 | + |
| -031 | 000 | 1.739 | 44.17 | 0.070 | 1.78 | 47.73 | ±0.015 | + |
| -032 | 000 | 1.864 | 47.35 | 0.070 | 1.78 | 50.90 | ±0.015 | + |
| -033 | 000 | 1.989 | 50.52 | 0.070 | 1.78 | 54.08 | ±0.018 | + |
| -034 | 000 | 2.114 | 53.70 | 0.070 | 1.78 | 57.25 | ±0.018 | + |
| -035 | 000 | 2.239 | 56.87 | 0.070 | 1.78 | 60.43 | ±0.018 | + |
| -036 | 000 | 2.364 | 60.05 | 0.070 | 1.78 | 63.60 | ±0.018 | + |
| -037 | 000 | 2.489 | 63.22 | 0.070 | 1.78 | 66.78 | ±0.018 | + |
| -038 | 000 | 2.614 | 66.40 | 0.070 | 1.78 | 69.95 | ±0.020 | + |
| -039 | 000 | 2.739 | 69.57 | 0.070 | 1.78 | 73.13 | ±0.020 | + |
| -040 | 000 | 2.864 | 72.75 | 0.070 | 1.78 | 76.30 | ±0.020 | + |
| -041 | 000 | 2.989 | 75.92 | 0.070 | 1.78 | 79.48 | ±0.024 | + |
| -042 | 000 | 3.239 | 82.27 | 0.070 | 1.78 | 85.83 | ±0.024 | + |
| -043 | 000 | 3.489 | 88.62 | 0.070 | 1.78 | 92.18 | ±0.024 | + |
| -044 | 000 | 3.739 | 94.97 | 0.070 | 1.78 | 98.53 | ±0.027 | + |
| -045 | 000 | 3.989 | 101.32 | 0.070 | 1.78 | 104.88 | ±0.027 | + |
| -046 | 000 | 4.239 | 107.67 | 0.070 | 1.78 | 111.23 | ±0.030 | + |
| -047 | 000 | 4.489 | 114.02 | 0.070 | 1.78 | 117.58 | ±0.030 | + |
| -048 | 000 | 4.739 | 120.37 | 0.070 | 1.78 | 123.93 | ±0.030 | + |
| -049 | 000 | 4.989 | 126.72 | 0.070 | 1.78 | 130.28 | ±0.037 | + |
| -050 | 000 | 5.239 | 133.07 | 0.070 | 1.78 | 136.63 | ±0.037 | + |
| -102 | 100 | 0.049 | 1.24 | 0.103 | 2.62 | 6.48 | ±0.005 | + |
| -103 | 100 | 0.081 | 2.06 | 0.103 | 2.62 | 7.29 | ±0.005 | + |
| -104 | 100 | 0.112 | 2.84 | 0.103 | 2.62 | 8.08 | ±0.005 | + |
| -105 | 100 | 0.143 | 3.63 | 0.103 | 2.62 | 8.86 | ±0.005 | + |
| -106 | 100 | 0.174 | 4.42 | 0.103 | 2.62 | 9.65 | ±0.005 | + |
| -107 | 100 | 0.206 | 5.23 | 0.103 | 2.62 | 10.46 | ±0.005 | + |
| -108 | 100 | 0.237 | 6.02 | 0.103 | 2.62 | 11.25 | ±0.005 | + |
| -109 | 100 | 0.299 | 7.59 | 0.103 | 2.62 | 12.83 | ±0.005 | + |
| -110 | 100 | 0.362 | 9.19 | 0.103 | 2.62 | 14.43 | ±0.005 | + |
| -111 | 100 | 0.424 | 10.77 | 0.103 | 2.62 | 16.00 | ±0.005 | + |
| -112 | 100 | 0.487 | 12.37 | 0.103 | 2.62 | 17.60 | ±0.005 | + |
| -113 | 100 | 0.549 | 13.94 | 0.103 | 2.62 | 19.18 | ±0.007 | + |
| -114 | 100 | 0.612 | 15.54 | 0.103 | 2.62 | 20.78 | ±0.009 | + |
| -115 | 100 | 0.674 | 17.12 | 0.103 | 2.62 | 22.35 | ±0.009 | + |
| -116 | 100 | 0.737 | 18.72 | 0.103 | 2.62 | 23.95 | ±0.009 | + |
| -117 | 100 | 0.799 | 20.29 | 0.103 | 2.62 | 25.53 | ±0.010 | + |
| -118 | 100 | 0.862 | 21.89 | 0.103 | 2.62 | 27.13 | ±0.010 | + |
| -119 | 100 | 0.924 | 23.47 | 0.103 | 2.62 | 28.70 | ±0.010 | + |
| -120 | 100 | 0.987 | 25.07 | 0.103 | 2.62 | 30.30 | ±0.010 | + |
| -121 | 100 | 1.049 | 26.64 | 0.103 | 2.62 | 31.88 | ±0.010 | + |
| -122 | 100 | 1.112 | 28.24 | 0.103 | 2.62 | 33.48 | ±0.010 | + |
| -123 | 100 | 1.174 | 29.82 | 0.103 | 2.62 | 35.05 | ±0.012 | + |
| -124 | 100 | 1.237 | 31.42 | 0.103 | 2.62 | 36.65 | ±0.012 | + |
| -125 | 100 | 1.299 | 32.99 | 0.103 | 2.62 | 38.23 | ±0.012 | + |
| -126 | 100 | 1.362 | 34.59 | 0.103 | 2.62 | 39.83 | ±0.012 | + |
| -127 | 100 | 1.424 | 36.17 | 0.103 | 2.62 | 41.40 | ±0.012 | + |
| -128 | 100 | 1.487 | 37.77 | 0.103 | 2.62 | 43.00 | ±0.012 | + |
| -129 | 100 | 1.549 | 39.34 | 0.103 | 2.62 | 44.58 | ±0.015 | + |
| -130 | 100 | 1.612 | 40.94 | 0.103 | 2.62 | 46.18 | ±0.015 | + |
| -131 | 100 | 1.674 | 42.52 | 0.103 | 2.62 | 47.75 | ±0.015 | + |
| -132 | 100 | 1.737 | 44.12 | 0.103 | 2.62 | 49.35 | ±0.015 | + |
| -133 | 100 | 1.799 | 45.69 | 0.103 | 2.62 | 50.93 | ±0.015 | + |
| -134 | 100 | 1.862 | 47.29 | 0.103 | 2.62 | 52.53 | ±0.015 | + |
| -135 | 100 | 1.925 | 48.89 | 0.103 | 2.62 | 54.13 | ±0.017 | + |
| -136 | 100 | 1.987 | 50.47 | 0.103 | 2.62 | 55.70 | ±0.017 | + |
| -137 | 100 | 2.050 | 52.07 | 0.103 | 2.62 | 57.30 | ±0.017 | + |
| -138 | 100 | 2.112 | 53.64 | 0.103 | 2.62 | 58.88 | ±0.017 | + |
| -139 | 100 | 2.175 | 55.24 | 0.103 | 2.62 | 60.48 | ±0.017 | + |
| -140 | 100 | 2.237 | 56.82 | 0.103 | 2.62 | 62.05 | ±0.017 | + |
| -141 | 100 | 2.300 | 58.42 | 0.103 | 2.62 | 63.65 | ±0.020 | + |
| -142 | 100 | 2.362 | 59.99 | 0.103 | 2.62 | 65.23 | ±0.020 | + |
| -143 | 100 | 2.425 | 61.59 | 0.103 | 2.62 | 66.83 | ±0.020 | + |
| -144 | 100 | 2.487 | 63.17 | 0.103 | 2.62 | 68.40 | ±0.020 | + |
| -145 | 100 | 2.550 | 64.77 | 0.103 | 2.62 | 70.00 | ±0.020 | + |
| -146 | 100 | 2.612 | 66.34 | 0.103 | 2.62 | 71.58 | ±0.020 | + |
| -147 | 100 | 2.675 | 67.94 | 0.103 | 2.62 | 73.18 | ±0.022 | + |
| -148 | 100 | 2.737 | 69.52 | 0.103 | 2.62 | 74.75 | ±0.022 | + |
| -149 | 100 | 2.800 | 71.12 | 0.103 | 2.62 | 76.35 | ±0.022 | + |
| -150 | 100 | 2.862 | 72.69 | 0.103 | 2.62 | 77.93 | ±0.022 | + |
| -151 | 100 | 2.987 | 75.87 | 0.103 | 2.62 | 81.10 | ±0.024 | + |
| -152 | 100 | 3.237 | 82.22 | 0.103 | 2.62 | 87.45 | ±0.024 | + |
| -153 | 100 | 3.487 | 88.57 | 0.103 | 2.62 | 93.80 | ±0.024 | + |
| -154 | 100 | 3.737 | 94.92 | 0.103 | 2.62 | 100.15 | ±0.028 | + |
| -155 | 100 | 3.987 | 101.27 | 0.103 | 2.62 | 106.50 | ±0.028 | + |
| -156 | 100 | 4.237 | 107.62 | 0.103 | 2.62 | 112.85 | ±0.030 | + |
| -157 | 100 | 4.487 | 113.97 | 0.103 | 2.62 | 119.20 | ±0.030 | + |
| -158 | 100 | 4.737 | 120.32 | 0.103 | 2.62 | 125.55 | ±0.030 | + |
| -159 | 100 | 4.987 | 126.67 | 0.103 | 2.62 | 131.90 | ±0.035 | + |
| -160 | 100 | 5.237 | 133.02 | 0.103 | 2.62 | 138.25 | ±0.035 | + |
| -161 | 100 | 5.487 | 139.37 | 0.103 | 2.62 | 144.60 | ±0.035 | + |
| -162 | 100 | 5.737 | 145.72 | 0.103 | 2.62 | 150.95 | ±0.035 | + |
| -163 | 100 | 5.987 | 152.07 | 0.103 | 2.62 | 157.30 | ±0.035 | + |
| -164 | 100 | 6.237 | 158.42 | 0.103 | 2.62 | 163.65 | ±0.040 | + |
| -165 | 100 | 6.487 | 164.77 | 0.103 | 2.62 | 170.00 | ±0.040 | + |
| -166 | 100 | 6.737 | 171.12 | 0.103 | 2.62 | 176.35 | ±0.040 | + |
| -167 | 100 | 6.987 | 177.47 | 0.103 | 2.62 | 182.70 | ±0.040 | + |
| -168 | 100 | 7.237 | 183.82 | 0.103 | 2.62 | 189.05 | ±0.045 | + |
| -169 | 100 | 7.487 | 190.17 | 0.103 | 2.62 | 195.40 | ±0.045 | + |
| -170 | 100 | 7.737 | 196.52 | 0.103 | 2.62 | 201.75 | ±0.045 | + |
| -171 | 100 | 7.987 | 202.87 | 0.103 | 2.62 | 208.10 | ±0.045 | + |
| -172 | 100 | 8.237 | 209.22 | 0.103 | 2.62 | 214.45 | ±0.050 | + |
| -173 | 100 | 8.487 | 215.57 | 0.103 | 2.62 | 220.80 | ±0.050 | + |
| -174 | 100 | 8.737 | 221.92 | 0.103 | 2.62 | 227.15 | ±0.050 | + |
| -175 | 100 | 8.987 | 228.27 | 0.103 | 2.62 | 233.50 | ±0.050 | + |
| -176 | 100 | 9.237 | 234.62 | 0.103 | 2.62 | 239.85 | ±0.055 | + |
| -177 | 100 | 9.487 | 240.97 | 0.103 | 2.62 | 246.20 | ±0.055 | + |
| -178 | 100 | 9.737 | 247.32 | 0.103 | 2.62 | 252.55 | ±0.055 | + |
| -201 | 200 | 0.171 | 4.34 | 0.139 | 3.53 | 11.40 | ±0.005 | + |
| -202 | 200 | 0.234 | 5.94 | 0.139 | 3.53 | 13.00 | ±0.005 | + |
| -203 | 200 | 0.296 | 7.52 | 0.139 | 3.53 | 14.58 | ±0.005 | + |
| -204 | 200 | 0.359 | 9.12 | 0.139 | 3.53 | 16.18 | ±0.005 | + |
| -205 | 200 | 0.421 | 10.69 | 0.139 | 3.53 | 17.75 | ±0.005 | + |
| -206 | 200 | 0.484 | 12.29 | 0.139 | 3.53 | 19.35 | ±0.005 | + |
| -207 | 200 | 0.546 | 13.87 | 0.139 | 3.53 | 20.93 | ±0.007 | + |
| -208 | 200 | 0.609 | 15.47 | 0.139 | 3.53 | 22.53 | ±0.009 | + |
| -209 | 200 | 0.671 | 17.04 | 0.139 | 3.53 | 24.10 | ±0.009 | + |
| -210 | 200 | 0.734 | 18.64 | 0.139 | 3.53 | 25.70 | ±0.010 | + |
| -211 | 200 | 0.796 | 20.22 | 0.139 | 3.53 | 27.28 | ±0.010 | + |
| -212 | 200 | 0.859 | 21.82 | 0.139 | 3.53 | 28.88 | ±0.010 | + |
| -213 | 200 | 0.921 | 23.39 | 0.139 | 3.53 | 30.45 | ±0.010 | + |
| -214 | 200 | 0.984 | 24.99 | 0.139 | 3.53 | 32.05 | ±0.010 | + |
| -215 | 200 | 1.046 | 26.57 | 0.139 | 3.53 | 33.63 | ±0.010 | + |
| -216 | 200 | 1.109 | 28.17 | 0.139 | 3.53 | 35.23 | ±0.012 | + |
| -217 | 200 | 1.171 | 29.74 | 0.139 | 3.53 | 36.80 | ±0.012 | + |
| -218 | 200 | 1.234 | 31.34 | 0.139 | 3.53 | 38.40 | ±0.012 | + |
| -219 | 200 | 1.296 | 32.92 | 0.139 | 3.53 | 39.98 | ±0.012 | + |
| -220 | 200 | 1.359 | 34.52 | 0.139 | 3.53 | 41.58 | ±0.012 | + |
| -221 | 200 | 1.421 | 36.09 | 0.139 | 3.53 | 43.15 | ±0.012 | + |
| -222 | 200 | 1.484 | 37.69 | 0.139 | 3.53 | 44.75 | ±0.015 | + |
| -223 | 200 | 1.609 | 40.87 | 0.139 | 3.53 | 47.93 | ±0.015 | + |
| -224 | 200 | 1.734 | 44.04 | 0.139 | 3.53 | 51.10 | ±0.015 | + |
| -225 | 200 | 1.859 | 47.22 | 0.139 | 3.53 | 54.28 | ±0.018 | + |
| -226 | 200 | 1.984 | 50.39 | 0.139 | 3.53 | 57.45 | ±0.018 | + |
| -227 | 200 | 2.109 | 53.57 | 0.139 | 3.53 | 60.63 | ±0.018 | + |
| -228 | 200 | 2.234 | 56.74 | 0.139 | 3.53 | 63.80 | ±0.020 | + |
| -229 | 200 | 2.359 | 59.92 | 0.139 | 3.53 | 66.98 | ±0.020 | + |
| -230 | 200 | 2.484 | 63.09 | 0.139 | 3.53 | 70.15 | ±0.020 | + |
| -231 | 200 | 2.609 | 66.27 | 0.139 | 3.53 | 73.33 | ±0.020 | + |
| -232 | 200 | 2.734 | 69.44 | 0.139 | 3.53 | 76.50 | ±0.024 | + |
| -233 | 200 | 2.859 | 72.62 | 0.139 | 3.53 | 79.68 | ±0.024 | + |
| -234 | 200 | 2.984 | 75.79 | 0.139 | 3.53 | 82.85 | ±0.024 | + |
| -235 | 200 | 3.109 | 78.97 | 0.139 | 3.53 | 86.03 | ±0.024 | + |
| -236 | 200 | 3.234 | 82.14 | 0.139 | 3.53 | 89.20 | ±0.024 | + |
| -237 | 200 | 3.359 | 85.32 | 0.139 | 3.53 | 92.38 | ±0.024 | + |
| -238 | 200 | 3.484 | 88.49 | 0.139 | 3.53 | 95.55 | ±0.024 | + |
| -239 | 200 | 3.609 | 91.67 | 0.139 | 3.53 | 98.73 | ±0.028 | + |
| -240 | 200 | 3.734 | 94.84 | 0.139 | 3.53 | 101.90 | ±0.028 | + |
| -241 | 200 | 3.859 | 98.02 | 0.139 | 3.53 | 105.08 | ±0.028 | + |
| -242 | 200 | 3.984 | 101.19 | 0.139 | 3.53 | 108.25 | ±0.028 | + |
| -243 | 200 | 4.109 | 104.37 | 0.139 | 3.53 | 111.43 | ±0.028 | + |
| -244 | 200 | 4.234 | 107.54 | 0.139 | 3.53 | 114.60 | ±0.030 | + |
| -245 | 200 | 4.359 | 110.72 | 0.139 | 3.53 | 117.78 | ±0.030 | + |
| -246 | 200 | 4.484 | 113.89 | 0.139 | 3.53 | 120.95 | ±0.030 | + |
| -247 | 200 | 4.609 | 117.07 | 0.139 | 3.53 | 124.13 | ±0.030 | + |
| -248 | 200 | 4.734 | 120.24 | 0.139 | 3.53 | 127.30 | ±0.030 | + |
| -249 | 200 | 4.859 | 123.42 | 0.139 | 3.53 | 130.48 | ±0.035 | + |
| -250 | 200 | 4.984 | 126.59 | 0.139 | 3.53 | 133.65 | ±0.035 | + |
| -251 | 200 | 5.109 | 129.77 | 0.139 | 3.53 | 136.83 | ±0.035 | + |
| -252 | 200 | 5.234 | 132.94 | 0.139 | 3.53 | 140.00 | ±0.035 | + |
| -253 | 200 | 5.359 | 136.12 | 0.139 | 3.53 | 143.18 | ±0.035 | + |
| -254 | 200 | 5.484 | 139.29 | 0.139 | 3.53 | 146.35 | ±0.035 | + |
| -255 | 200 | 5.609 | 142.47 | 0.139 | 3.53 | 149.53 | ±0.035 | + |
| -256 | 200 | 5.734 | 145.64 | 0.139 | 3.53 | 152.70 | ±0.035 | + |
| -257 | 200 | 5.859 | 148.82 | 0.139 | 3.53 | 155.88 | ±0.035 | + |
| -258 | 200 | 5.984 | 151.99 | 0.139 | 3.53 | 159.05 | ±0.035 | + |
| -259 | 200 | 6.234 | 158.34 | 0.139 | 3.53 | 165.40 | ±0.040 | + |
| -260 | 200 | 6.484 | 164.69 | 0.139 | 3.53 | 171.75 | ±0.040 | + |
| -261 | 200 | 6.734 | 171.04 | 0.139 | 3.53 | 178.10 | ±0.040 | + |
| -262 | 200 | 6.984 | 177.39 | 0.139 | 3.53 | 184.45 | ±0.040 | + |
| -263 | 200 | 7.234 | 183.74 | 0.139 | 3.53 | 190.80 | ±0.045 | + |
| -264 | 200 | 7.484 | 190.09 | 0.139 | 3.53 | 197.15 | ±0.045 | + |
| -265 | 200 | 7.734 | 196.44 | 0.139 | 3.53 | 203.50 | ±0.045 | + |
| -266 | 200 | 7.984 | 202.79 | 0.139 | 3.53 | 209.85 | ±0.045 | + |
| -267 | 200 | 8.234 | 209.14 | 0.139 | 3.53 | 216.20 | ±0.050 | + |
| -268 | 200 | 8.484 | 215.49 | 0.139 | 3.53 | 222.55 | ±0.050 | + |
| -269 | 200 | 8.734 | 221.84 | 0.139 | 3.53 | 228.90 | ±0.050 | + |
| -270 | 200 | 8.984 | 228.19 | 0.139 | 3.53 | 235.25 | ±0.050 | + |
| -271 | 200 | 9.234 | 234.54 | 0.139 | 3.53 | 241.60 | ±0.055 | + |
| -272 | 200 | 9.484 | 240.89 | 0.139 | 3.53 | 247.95 | ±0.055 | + |
| -273 | 200 | 9.734 | 247.24 | 0.139 | 3.53 | 254.30 | ±0.055 | + |
| -274 | 200 | 9.984 | 253.59 | 0.139 | 3.53 | 260.65 | ±0.055 | + |
| -275 | 200 | 10.484 | 266.29 | 0.139 | 3.53 | 273.35 | ±0.055 | + |
| -276 | 200 | 10.984 | 278.99 | 0.139 | 3.53 | 286.05 | ±0.065 | + |
| -277 | 200 | 11.484 | 291.69 | 0.139 | 3.53 | 298.75 | ±0.065 | + |
| -278 | 200 | 11.984 | 304.39 | 0.139 | 3.53 | 311.45 | ±0.065 | + |
| -279 | 200 | 12.984 | 329.79 | 0.139 | 3.53 | 336.85 | ±0.065 | + |
| -280 | 200 | 13.984 | 355.19 | 0.139 | 3.53 | 362.25 | ±0.065 | + |
| -281 | 200 | 14.984 | 380.59 | 0.139 | 3.53 | 387.65 | ±0.065 | + |
| -282 | 200 | 15.955 | 405.26 | 0.139 | 3.53 | 412.32 | ±0.075 | + |
| -283 | 200 | 16.955 | 430.66 | 0.139 | 3.53 | 437.72 | ±0.080 | + |
| -284 | 200 | 17.955 | 456.06 | 0.139 | 3.53 | 463.12 | ±0.085 | + |
| -309 | 300 | 0.412 | 10.46 | 0.210 | 5.33 | 21.13 | ±0.005 | + |
| -310 | 300 | 0.475 | 12.06 | 0.210 | 5.33 | 22.73 | ±0.005 | + |
| -311 | 300 | 0.537 | 13.64 | 0.210 | 5.33 | 24.31 | ±0.007 | + |
| -312 | 300 | 0.600 | 15.24 | 0.210 | 5.33 | 25.91 | ±0.009 | + |
| -313 | 300 | 0.662 | 16.81 | 0.210 | 5.33 | 27.48 | ±0.009 | + |
| -314 | 300 | 0.725 | 18.41 | 0.210 | 5.33 | 29.08 | ±0.010 | + |
| -315 | 300 | 0.787 | 19.99 | 0.210 | 5.33 | 30.66 | ±0.010 | + |
| -316 | 300 | 0.850 | 21.59 | 0.210 | 5.33 | 32.26 | ±0.010 | + |
| -317 | 300 | 0.912 | 23.16 | 0.210 | 5.33 | 33.83 | ±0.010 | + |
| -318 | 300 | 0.975 | 24.76 | 0.210 | 5.33 | 35.43 | ±0.010 | + |
| -319 | 300 | 1.037 | 26.34 | 0.210 | 5.33 | 37.01 | ±0.010 | + |
| -320 | 300 | 1.100 | 27.94 | 0.210 | 5.33 | 38.61 | ±0.012 | + |
| -321 | 300 | 1.162 | 29.51 | 0.210 | 5.33 | 40.18 | ±0.012 | + |
| -322 | 300 | 1.225 | 31.12 | 0.210 | 5.33 | 41.78 | ±0.012 | + |
| -323 | 300 | 1.287 | 32.69 | 0.210 | 5.33 | 43.36 | ±0.012 | + |
| -324 | 300 | 1.350 | 34.29 | 0.210 | 5.33 | 44.96 | ±0.012 | + |
| -325 | 300 | 1.475 | 37.47 | 0.210 | 5.33 | 48.13 | ±0.015 | + |
| -326 | 300 | 1.600 | 40.64 | 0.210 | 5.33 | 51.31 | ±0.015 | + |
| -327 | 300 | 1.725 | 43.81 | 0.210 | 5.33 | 54.48 | ±0.015 | + |
| -328 | 300 | 1.850 | 46.99 | 0.210 | 5.33 | 57.66 | ±0.015 | + |
| -329 | 300 | 1.975 | 50.16 | 0.210 | 5.33 | 60.83 | ±0.018 | + |
| -330 | 300 | 2.100 | 53.34 | 0.210 | 5.33 | 64.01 | ±0.018 | + |
| -331 | 300 | 2.225 | 56.52 | 0.210 | 5.33 | 67.18 | ±0.018 | + |
| -332 | 300 | 2.350 | 59.69 | 0.210 | 5.33 | 70.36 | ±0.018 | + |
| -333 | 300 | 2.475 | 62.87 | 0.210 | 5.33 | 73.53 | ±0.020 | + |
| -334 | 300 | 2.600 | 66.04 | 0.210 | 5.33 | 76.71 | ±0.020 | + |
| -335 | 300 | 2.725 | 69.22 | 0.210 | 5.33 | 79.88 | ±0.020 | + |
| -336 | 300 | 2.850 | 72.39 | 0.210 | 5.33 | 83.06 | ±0.020 | + |
| -337 | 300 | 2.975 | 75.56 | 0.210 | 5.33 | 86.23 | ±0.024 | + |
| -338 | 300 | 3.100 | 78.74 | 0.210 | 5.33 | 89.41 | ±0.024 | + |
| -339 | 300 | 3.225 | 81.91 | 0.210 | 5.33 | 92.58 | ±0.024 | + |
| -340 | 300 | 3.350 | 85.09 | 0.210 | 5.33 | 95.76 | ±0.024 | + |
| -341 | 300 | 3.475 | 88.27 | 0.210 | 5.33 | 98.93 | ±0.024 | + |
| -342 | 300 | 3.600 | 91.44 | 0.210 | 5.33 | 102.11 | ±0.028 | + |
| -343 | 300 | 3.725 | 94.61 | 0.210 | 5.33 | 105.28 | ±0.028 | + |
| -344 | 300 | 3.850 | 97.79 | 0.210 | 5.33 | 108.46 | ±0.028 | + |
| -345 | 300 | 3.975 | 100.97 | 0.210 | 5.33 | 111.63 | ±0.028 | + |
| -346 | 300 | 4.100 | 104.14 | 0.210 | 5.33 | 114.81 | ±0.028 | + |
| -347 | 300 | 4.225 | 107.31 | 0.210 | 5.33 | 117.98 | ±0.030 | + |
| -348 | 300 | 4.350 | 110.49 | 0.210 | 5.33 | 121.16 | ±0.030 | + |
| -349 | 300 | 4.475 | 113.66 | 0.210 | 5.33 | 124.33 | ±0.030 | + |
| -350 | 300 | 4.600 | 116.84 | 0.210 | 5.33 | 127.51 | ±0.030 | + |
| -351 | 300 | 4.725 | 120.01 | 0.210 | 5.33 | 130.68 | ±0.030 | + |
| -352 | 300 | 4.850 | 123.19 | 0.210 | 5.33 | 133.86 | ±0.030 | + |
| -353 | 300 | 4.975 | 126.36 | 0.210 | 5.33 | 137.03 | ±0.037 | + |
| -354 | 300 | 5.100 | 129.54 | 0.210 | 5.33 | 140.21 | ±0.037 | + |
| -355 | 300 | 5.225 | 132.71 | 0.210 | 5.33 | 143.38 | ±0.037 | + |
| -356 | 300 | 5.350 | 135.89 | 0.210 | 5.33 | 146.56 | ±0.037 | + |
| -357 | 300 | 5.475 | 139.06 | 0.210 | 5.33 | 149.73 | ±0.037 | + |
| -358 | 300 | 5.600 | 142.24 | 0.210 | 5.33 | 152.91 | ±0.037 | + |
| -359 | 300 | 5.725 | 145.41 | 0.210 | 5.33 | 156.08 | ±0.037 | + |
| -360 | 300 | 5.850 | 148.59 | 0.210 | 5.33 | 159.26 | ±0.037 | + |
| -361 | 300 | 5.975 | 151.76 | 0.210 | 5.33 | 162.43 | ±0.037 | + |
| -362 | 300 | 6.225 | 158.11 | 0.210 | 5.33 | 168.78 | ±0.040 | + |
| -363 | 300 | 6.475 | 164.46 | 0.210 | 5.33 | 175.13 | ±0.040 | + |
| -364 | 300 | 6.725 | 170.81 | 0.210 | 5.33 | 181.48 | ±0.040 | + |
| -365 | 300 | 6.975 | 177.16 | 0.210 | 5.33 | 187.83 | ±0.040 | + |
| -366 | 300 | 7.225 | 183.51 | 0.210 | 5.33 | 194.18 | ±0.045 | + |
| -367 | 300 | 7.475 | 189.86 | 0.210 | 5.33 | 200.53 | ±0.045 | + |
| -368 | 300 | 7.725 | 196.21 | 0.210 | 5.33 | 206.88 | ±0.045 | + |
| -369 | 300 | 7.975 | 202.56 | 0.210 | 5.33 | 213.23 | ±0.045 | + |
| -370 | 300 | 8.225 | 208.91 | 0.210 | 5.33 | 219.58 | ±0.050 | + |
| -371 | 300 | 8.475 | 215.26 | 0.210 | 5.33 | 225.93 | ±0.050 | + |
| -372 | 300 | 8.725 | 221.61 | 0.210 | 5.33 | 232.28 | ±0.050 | + |
| -373 | 300 | 8.975 | 227.96 | 0.210 | 5.33 | 238.63 | ±0.050 | + |
| -374 | 300 | 9.225 | 234.31 | 0.210 | 5.33 | 244.98 | ±0.055 | + |
| -375 | 300 | 9.475 | 240.66 | 0.210 | 5.33 | 251.33 | ±0.055 | + |
| -376 | 300 | 9.725 | 247.01 | 0.210 | 5.33 | 257.68 | ±0.055 | + |
| -377 | 300 | 9.975 | 253.36 | 0.210 | 5.33 | 264.03 | ±0.055 | + |
| -378 | 300 | 10.475 | 266.06 | 0.210 | 5.33 | 276.73 | ±0.060 | + |
| -379 | 300 | 10.975 | 278.76 | 0.210 | 5.33 | 289.43 | ±0.060 | + |
| -380 | 300 | 11.475 | 291.46 | 0.210 | 5.33 | 302.13 | ±0.065 | + |
| -381 | 300 | 11.975 | 304.16 | 0.210 | 5.33 | 314.83 | ±0.065 | + |
| -382 | 300 | 12.975 | 329.56 | 0.210 | 5.33 | 340.23 | ±0.065 | + |
| -383 | 300 | 13.975 | 354.96 | 0.210 | 5.33 | 365.63 | ±0.070 | + |
| -384 | 300 | 14.975 | 380.36 | 0.210 | 5.33 | 391.03 | ±0.070 | + |
| -385 | 300 | 15.955 | 405.26 | 0.210 | 5.33 | 415.92 | ±0.075 | + |
| -386 | 300 | 16.955 | 430.66 | 0.210 | 5.33 | 441.32 | ±0.080 | + |
| -387 | 300 | 17.955 | 456.06 | 0.210 | 5.33 | 466.72 | ±0.085 | + |
| -388 | 300 | 18.955 | 481.46 | 0.210 | 5.33 | 492.12 | ±0.090 | + |
| -389 | 300 | 19.955 | 506.86 | 0.210 | 5.33 | 517.52 | ±0.095 | + |
| -390 | 300 | 20.955 | 532.26 | 0.210 | 5.33 | 542.92 | ±0.095 | + |
| -391 | 300 | 21.955 | 557.66 | 0.210 | 5.33 | 568.32 | ±0.100 | + |
| -392 | 300 | 22.940 | 582.68 | 0.210 | 5.33 | 593.34 | ±0.105 | + |
| -393 | 300 | 23.940 | 608.08 | 0.210 | 5.33 | 618.74 | ±0.110 | + |
| -394 | 300 | 24.940 | 633.48 | 0.210 | 5.33 | 644.14 | ±0.115 | + |
| -395 | 300 | 25.940 | 658.88 | 0.210 | 5.33 | 669.54 | ±0.120 | + |
| -425 | 400 | 4.475 | 113.66 | 0.275 | 6.99 | 127.63 | ±0.033 | + |
| -426 | 400 | 4.600 | 116.84 | 0.275 | 6.99 | 130.81 | ±0.033 | + |
| -427 | 400 | 4.725 | 120.01 | 0.275 | 6.99 | 133.98 | ±0.033 | + |
| -428 | 400 | 4.850 | 123.19 | 0.275 | 6.99 | 137.16 | ±0.033 | + |
| -429 | 400 | 4.975 | 126.36 | 0.275 | 6.99 | 140.33 | ±0.037 | + |
| -430 | 400 | 5.100 | 129.54 | 0.275 | 6.99 | 143.51 | ±0.037 | + |
| -431 | 400 | 5.225 | 132.71 | 0.275 | 6.99 | 146.68 | ±0.037 | + |
| -432 | 400 | 5.350 | 135.89 | 0.275 | 6.99 | 149.86 | ±0.037 | + |
| -433 | 400 | 5.475 | 139.06 | 0.275 | 6.99 | 153.03 | ±0.037 | + |
| -434 | 400 | 5.600 | 142.24 | 0.275 | 6.99 | 156.21 | ±0.037 | + |
| -435 | 400 | 5.725 | 145.41 | 0.275 | 6.99 | 159.38 | ±0.037 | + |
| -436 | 400 | 5.850 | 148.59 | 0.275 | 6.99 | 162.56 | ±0.037 | + |
| -437 | 400 | 5.975 | 151.76 | 0.275 | 6.99 | 165.73 | ±0.037 | + |
| -438 | 400 | 6.225 | 158.11 | 0.275 | 6.99 | 172.08 | ±0.040 | + |
| -439 | 400 | 6.475 | 164.46 | 0.275 | 6.99 | 178.43 | ±0.040 | + |
| -440 | 400 | 6.725 | 170.81 | 0.275 | 6.99 | 184.78 | ±0.040 | + |
| -441 | 400 | 6.975 | 177.16 | 0.275 | 6.99 | 191.13 | ±0.040 | + |
| -442 | 400 | 7.225 | 183.51 | 0.275 | 6.99 | 197.48 | ±0.045 | + |
| -443 | 400 | 7.475 | 189.86 | 0.275 | 6.99 | 203.84 | ±0.045 | + |
| -444 | 400 | 7.725 | 196.21 | 0.275 | 6.99 | 210.19 | ±0.045 | + |
| -445 | 400 | 7.975 | 202.56 | 0.275 | 6.99 | 216.53 | ±0.045 | + |
| -446 | 400 | 8.475 | 215.26 | 0.275 | 6.99 | 229.23 | ±0.055 | + |
| -447 | 400 | 8.975 | 227.96 | 0.275 | 6.99 | 241.94 | ±0.055 | + |
| -448 | 400 | 9.475 | 240.66 | 0.275 | 6.99 | 254.63 | ±0.055 | + |
| -449 | 400 | 9.975 | 253.36 | 0.275 | 6.99 | 267.33 | ±0.055 | + |
| -450 | 400 | 10.475 | 266.06 | 0.275 | 6.99 | 280.03 | ±0.060 | + |
| -451 | 400 | 10.975 | 278.76 | 0.275 | 6.99 | 292.74 | ±0.060 | + |
| -452 | 400 | 11.475 | 291.46 | 0.275 | 6.99 | 305.44 | ±0.060 | + |
| -453 | 400 | 11.975 | 304.16 | 0.275 | 6.99 | 318.13 | ±0.060 | + |
| -454 | 400 | 12.475 | 316.86 | 0.275 | 6.99 | 330.83 | ±0.060 | + |
| -455 | 400 | 12.975 | 329.56 | 0.275 | 6.99 | 343.53 | ±0.060 | + |
| -456 | 400 | 13.475 | 342.26 | 0.275 | 6.99 | 356.24 | ±0.070 | + |
| -457 | 400 | 13.975 | 354.96 | 0.275 | 6.99 | 368.94 | ±0.070 | + |
| -458 | 400 | 14.475 | 367.66 | 0.275 | 6.99 | 381.63 | ±0.070 | + |
| -459 | 400 | 14.975 | 380.36 | 0.275 | 6.99 | 394.33 | ±0.070 | + |
| -460 | 400 | 15.475 | 393.06 | 0.275 | 6.99 | 407.03 | ±0.070 | + |
| -461 | 400 | 15.955 | 405.26 | 0.275 | 6.99 | 419.23 | ±0.075 | + |
| -462 | 400 | 16.455 | 417.96 | 0.275 | 6.99 | 431.93 | ±0.075 | + |
| -463 | 400 | 16.955 | 430.66 | 0.275 | 6.99 | 444.63 | ±0.080 | + |
| -464 | 400 | 17.455 | 443.36 | 0.275 | 6.99 | 457.33 | ±0.085 | + |
| -465 | 400 | 17.955 | 456.06 | 0.275 | 6.99 | 470.03 | ±0.085 | + |
| -466 | 400 | 18.455 | 468.76 | 0.275 | 6.99 | 482.73 | ±0.085 | + |
| -467 | 400 | 18.955 | 481.46 | 0.275 | 6.99 | 495.43 | ±0.090 | + |
| -468 | 400 | 19.455 | 494.16 | 0.275 | 6.99 | 508.13 | ±0.090 | + |
| -469 | 400 | 19.955 | 506.86 | 0.275 | 6.99 | 520.83 | ±0.090 | + |
| -470 | 400 | 20.955 | 532.26 | 0.275 | 6.99 | 546.23 | ±0.090 | + |
| -471 | 400 | 21.955 | 557.66 | 0.275 | 6.99 | 571.63 | ±0.100 | + |
| -472 | 400 | 22.940 | 582.68 | 0.275 | 6.99 | 596.65 | ±0.105 | + |
| -473 | 400 | 23.940 | 608.08 | 0.275 | 6.99 | 622.05 | ±0.110 | + |
| -474 | 400 | 24.940 | 633.48 | 0.275 | 6.99 | 647.45 | ±0.115 | + |
| -475 | 400 | 25.940 | 658.88 | 0.275 | 6.99 | 672.85 | ±0.120 | + |
Use + at the end of a row to keep that size. The list follows you to the other charts. Material and quantity can be set per size in the tray, and the enquiry form opens with those lines ready.
Look Up a Size
Interactive Lookup
Two ways in: type the dash number if you have one, or enter the dimensions you measured and compare them with the closest standard sizes.
By dash number
For example 214 or -214. The result also fills the weight calculator below with the ID and CS of that size.
By measured dimensions
The five closest AS568 sizes are listed with the difference in inside diameter.
O-ring weight calculator
Estimate the weight of a ring from its dimensions, using the torus volume formula and typical compound densities. Type a dash number in the lookup above and this calculator picks up the ID and CS of that size automatically.
Note: every supplier works with its own compound formulation, so densities differ from one maker to the next. Treat the calculated weight as a reference figure only. The actual weight of the finished part is what counts.
What an AS568 Dash Number Tells You
The dash number is not a random part number. The first digit of the three digit number gives the cross section series, and the remaining digits give the position of the size inside that series. That is why a -110 and a -210 have the same last two digits but different cross sections.
| Series | Dash range in this chart | CS (in) | CS (mm) | ID (in) | ID (mm) | Sizes |
|---|---|---|---|---|---|---|
| 000 | -001 to -050 | 0.040 to 0.070 | 1.02 to 1.78 | 0.029 to 5.239 | 0.74 to 133.07 | 51 |
| 100 | -102 to -178 | 0.103 to 0.103 | 2.62 to 2.62 | 0.049 to 9.737 | 1.24 to 247.32 | 77 |
| 200 | -201 to -284 | 0.139 to 0.139 | 3.53 to 3.53 | 0.171 to 17.955 | 4.34 to 456.06 | 84 |
| 300 | -309 to -395 | 0.210 to 0.210 | 5.33 to 5.33 | 0.412 to 25.940 | 10.46 to 658.88 | 87 |
| 400 | -425 to -475 | 0.275 to 0.275 | 6.99 to 6.99 | 4.475 to 25.940 | 113.66 to 658.88 | 51 |
The 900 series (tube fitting seals) and the 001½ size are outside the main series logic. We quote the 900 series on request; 001½ is listed in the table above. The 000 series also contains three sizes with a thinner cord than the rest of the series, -001 to -003.
The Five Cross Section Series
The first digit of every dash number fixes the cross section. The table gives the cord of each series and where it is normally used.
| Series | Cord | Where it is used |
|---|---|---|
| 000 | 0.040 to 0.070 in 1.02 to 1.78 mm |
Small rings on sensors, small pneumatic fittings and thin-wall housings where a larger cord would not fit the groove. |
| 100 | 0.103 in 2.62 mm |
The most widely used cord in general industrial equipment. Inside diameters in this chart run from 1.24 mm to 247.32 mm. |
| 200 | 0.139 in 3.53 mm |
Most hydraulic and pneumatic components. The -2xx numbers are the ones we are asked for most often. |
| 300 | 0.210 in 5.33 mm |
Larger flanges, valves and housings where the groove is wider and the joint is less rigid. |
| 400 | 0.275 in 6.99 mm |
Heavy cord for large-diameter static joints, tank covers and pipe flanges up to 658.88 mm inside diameter. |
Widths are the nominal cord of each series. The 000 series also contains three sizes with a thinner cord, -001 to -003, all listed in the chart above.
How to Measure an O-Ring Correctly
- Measure the inside diameter, not the outside diameter. The inside diameter and the cross section define the size. The outside diameter is a result: OD = ID + 2 x CS.
- Do not stretch the ring over a cone or a caliper jaw. An elastic ring pulled open reads larger than it is, and the error is often bigger than the tolerance band.
- Measure a new ring where possible. A used ring has taken a compression set and may have swollen in oil, so it reads different from the drawing.
- Check the cross section in two places at 90 degrees. An oval or worn ring gives two different readings, and both matter.
- Use the tolerance, not the nominal figure. Two rings can both be -214 and differ by the tolerance band on diameter and cord.
If you are cutting a new groove rather than matching a size that already exists, the groove design page carries the gland depth and groove width bands for the same cross sections, plus a checker that turns a measured groove into squeeze and fill.
Tolerances And Acceptance
AS568 fixes a band on every dash number, and the band is part of the size rather than a note on it. Two rings can both be -214 and still differ by the permitted deviation, which is why a complaint about a size that does not match the chart usually turns out to be a reading taken outside the band.
The Band The Dash Number Carries
The cord tolerance depends on the cross section, not on the number:
| Series | Cord (mm) | Cord tolerance |
|---|---|---|
| 000, -001 to -003 | 1.02 | ±0.08 |
| 000 | 1.78 | ±0.08 |
| 100 | 2.62 | ±0.08 |
| 200 | 3.53 | ±0.10 |
| 300 | 5.33 | ±0.13 |
| 400 | 6.99 | ±0.15 |
The inside diameter band grows with the ring, because a larger mould has more shrinkage to control. Five sizes across the range show the step:
| Dash number | Inside diameter (mm) | ID tolerance | Cord (mm) |
|---|---|---|---|
| -001 | 0.74 | ±0.10 | 1.02 |
| -010 | 6.07 | ±0.13 | 1.78 |
| -214 | 24.99 | ±0.25 | 3.53 |
| -136 | 50.47 | ±0.43 | 2.62 |
| -425 | 113.66 | ±0.84 | 6.99 |
The step is neither linear nor uniform across the list. A -010 at 6.07 mm is held to 0.13 mm while a -425 at 113.66 mm is held to 0.84 mm: nineteen times the diameter, six and a half times the band. That is why the figure has to travel with the size, and why a ring quoted only by its dash number is not fully specified.
Class A And Class B On The Same Size
AS568 defines two tolerance classes for the same dash number. Class A is the tighter class and Class B the commercial one. The dimensions are identical, only the permitted deviation changes, so a Class B ring can measure outside the Class A band without being defective. If the groove was designed around a Class A ring, that difference is enough to change the squeeze. We confirm the class on the quotation, and our rubber seal tolerance guide explains the bands in detail.
What We Accept At Inspection
| What is checked | What we hold | Where it is written |
|---|---|---|
| Inside diameter and cross section | The band the standard prints for that size, not the nominal figure | Quotation and inspection sheet |
| Surface and visual defects | The grade named on the drawing. Where the drawing is silent we work to ISO 3601-3 grade N | Quotation, and the sample you approve |
| Hardness | ±5 Shore A around the nominal figure | Test certificate |
| Compound and cure | The compound quoted, batch traceable | Certificate of conformity on request |
| Tolerance tighter than the standard | Quoted case by case, because it is a moulding capability question and not a paperwork one | Drawing and agreed deviation |
When A Ring Measures Outside
Every production lot is sampled against the band before it is packed. A lot that falls outside is held, and you hear it from us before it ships. The options are a remake, shipment against a written deviation you have accepted, or a credit. Shipping it and letting the difference turn up at your incoming inspection is not one of them.
Dimensions are checked on rings that have lain free and unstressed for at least an hour at 23 °C and 50 % relative humidity, as ISO 23529 sets out. Inside diameter is read with a taper gauge or a calibrated plug, cross section with a micrometer at light closing pressure. A ring measured while stretched, or straight off a warm press, will not agree with the band it was made to.
The bands on this page are the ones we work to in normal production. Where this page and the text of the standard disagree, the standard text governs, and where your drawing is tighter than the standard, the drawing governs.
Inch Sizes Against Metric and Japanese Sizes
An AS568 size is an inch size. A metric ring of the same nominal inside diameter usually has a different cord: 2.62 mm against 2.65 mm, or 3.53 mm against 3.55 mm. The two are close but not the same part, and the groove is cut for one of them. If your drawing quotes ISO 3601, JIS B 2401, BS 1806 or DIN 3771 instead of a dash number, use the O-ring standard cross reference before converting anything.
The metric and British lists are on their own charts: ISO 3601 (Class A and Class B), JIS B 2401 (P, G, S, SS and V series) and BS 1806. Each one accepts either the code or a measured inside diameter and cross section, so a ring with no readable marking can still be placed.
Ordering From This Chart
Send the dash number or the two dimensions, the compound, the hardness, and the quantity. If the application runs at temperature, in a solvent, or in a food or drinking water line, tell us the medium as well, because the compound matters more than the size at that point.
Standard sizes are on our O-ring product page, and if you need a workshop assortment rather than single sizes, see the O-ring kits and assortments page. For rings outside this chart, we produce to drawing, including metric sizes and non-standard cords.
Frequently Asked Questions
Is the AS568 chart the same as an ISO 3601 chart?
ISO 3601 Class A uses the same sizes and dash numbers as AS568, so the numbers can be read from this chart. ISO 3601 Class B is a separate metric list with its own codes, so a Class B number cannot be read from an AS568 table.
Why does my -214 measure differently from the chart?
The chart gives the nominal figure. Each size has a tolerance band on the inside diameter and on the cord, and a new ring can sit anywhere inside that band. Check the tolerance column before rejecting a ring.
Do you supply sizes beyond -475?
Yes. Sizes above the standard range, split rings, and bonded or vulcanised joints for very large diameters are quoted from drawing.
Can you supply the same size in a different cord?
Only by making a new mould. A -214 with a 5.33 mm cord is not a standard part. Send the drawing and we will confirm what is possible.
Request a Quote
Send the dash numbers and quantities, or the measured dimensions if the size is not standard, and we will reply with the compound options and price.
