Bonded Seal Size Chart: Metric and Imperial Size Numbers

A bonded seal is a metal washer with an elastomer bead bonded into the bore. It seals a threaded port on the flat face rather than on the thread, which is why it holds pressure that a copper washer cannot and why it is the standard seal on hydraulic ports, gearbox drain plugs and pressure test points.

The size is a number, and the number is the only practical way to order one. A two hundred number is a metric thread size, a number below a hundred is an imperial or BSP thread size. This page lists both ranges with the four dimensions a port is checked against, and adds a lookup that takes either the size number or the thread size.

Two Number Ranges

Range Size numbers Threads covered Washer thickness Sizes in this chart
Metric 201 to 255 M3.5 to M125 1.00 to 5.00 mm 53
Imperial and BSP 001 to 039 6BA to 3-1/2 inch 1.22 to 3.25 mm 39

The two ranges are not interchangeable and do not overlap. A metric port measuring 20 mm across the thread takes a two hundred number; a 3/4 inch BSP port takes a number in the thirties. Where a fitting is marked only with its thread, the lookup below will list the washers made for that thread in both ranges.

Metric Size Chart

Ordered by thread size, which is how a port is normally identified. D is the outside diameter, d and d1 are the two bore diameters, and S is the washer thickness.

Size no. Thread D (mm) d (mm) d1 (mm) S (mm) Quote
201 3.5 7.20 4.10 5.20 1.00 +
202 4 7.00 4.50 5.40 1.00 +
203 5 9.00 5.70 6.80 1.00 +
204 5 10.00 5.70 7.40 1.00 +
205 5.5 9.20 6.20 7.20 1.00 +
206 6 10.00 6.70 8.00 1.00 +
207 6 11.00 6.70 8.20 1.00 +
208 6 11.00 6.70 8.20 2.50 +
209 6.5 12.00 7.10 8.80 1.00 +
210 6.7 10.20 7.30 8.60 1.00 +
211 8 13.40 8.50 9.40 1.00 +
212 8 13.00 8.70 10.00 1.00 +
213 8 14.00 8.70 10.40 1.00 +
214 8 16.00 8.70 10.40 1.00 +
215 8.5 13.30 9.30 10.50 1.00 +
216 10 16.00 10.35 12.00 2.00 +
217 10 16.00 10.70 12.40 1.50 +
218 10 18.00 10.70 12.40 1.50 +
219 11 16.30 11.40 12.70 1.50 +
220 11 18.50 11.80 13.70 1.50 +
221 11 19.10 11.80 13.50 1.50 +
222 12 18.00 12.70 14.40 1.50 +
223 12 20.00 12.70 14.40 1.50 +
224 13 20.00 13.70 15.40 1.50 +
225 13 22.00 13.70 15.40 1.50 +
226 13.5 18.70 14.00 15.70 1.50 +
227 14 22.00 14.70 16.40 1.50 +
228 15 22.70 16.00 17.78 1.50 +
229 16 24.00 16.70 18.40 1.50 +
230 17 24.00 17.40 19.20 1.50 +
231 17.5 24.70 18.00 20.10 1.50 +
232 18 26.00 18.70 20.40 1.50 +
233 20 28.00 20.70 22.50 1.50 +
234 21 28.70 21.50 23.30 2.50 +
235 22 28.00 22.50 24.20 1.50 +
236 22 30.00 22.70 24.40 2.00 +
237 22 30.00 22.70 24.40 3.00 +
238 24 32.00 24.70 26.40 2.00 +
240 27 36.00 27.20 29.00 2.00 +
242 30 39.00 31.00 33.00 2.00 +
243 33 42.00 33.70 35.80 2.00 +
244 33 43.00 34.30 36.40 2.00 +
245 36 46.00 36.70 38.80 2.00 +
246 39 51.00 40.00 41.90 2.50 +
247 42 53.00 42.70 44.40 3.00 +
248 48 59.00 48.70 50.80 3.00 +
249 51 60.00 52.00 54.10 3.00 +
250 52 64.50 53.30 56.40 3.00 +
251 60 73.00 60.70 63.00 3.00 +
252 68 79.50 68.60 72.10 3.50 +
253 75 90.30 76.08 79.10 3.38 +
254 88 101.48 89.09 92.10 3.25 +
255 125 143.67 127.00 132.70 5.00 +

Use + at the end of a row to keep that size. The list follows you to the other charts. Material and quantity can be set per size in the tray, and the enquiry form opens with those lines ready.

Imperial And BSP Size Chart

The same four dimensions for the imperial range, ordered by size number. The thread column gives the thread the washer is intended for, from 6BA on the smallest sizes to 3-1/2 inch BSP.

Size no. Thread D (mm) d (mm) d1 (mm) S (mm) Quote
001 6BA 6.35 3.05 4.09 1.22 +
002 4BA 7.26 4.12 5.26 1.22 +
003 2BA 8.38 5.21 6.35 1.22 +
004 1/4 13.21 6.86 8.00 1.22 +
005 1/4 13.34 6.99 9.53 1.22 +
006 3/8 13.34 8.31 9.53 1.22 +
007 3/8 14.22 8.64 10.04 1.22 +
008 5/16 18.36 11.26 12.45 2.00 +
009 3/8 19.05 11.69 13.08 2.00 +
010 1/2 22.23 14.86 16.39 2.00 +
011 1/2 25.40 16.51 18.75 2.00 +
012 5/8 25.40 18.16 19.69 2.34 +
013 1 33.27 24.26 26.04 2.34 +
014 1-1/8 36.58 29.33 30.86 2.34 +
015 1-1/4 41.40 32.64 35.69 3.25 +
016 1-1/2 44.45 35.94 38.99 2.34 +
017 1-5/8 47.75 38.96 42.04 2.34 +
018 1-7/8 57.15 45.34 48.39 2.34 +
019 2 63.50 51.69 54.74 2.34 +
020 1/8 15.88 10.37 11.84 2.00 +
021 1/4 20.57 13.74 15.21 2.00 +
022 7/8 22.23 15.83 17.30 2.00 +
023 3/4 23.80 17.28 18.75 2.00 +
024 3/4 26.92 19.69 21.21 2.34 +
025 7/8 28.58 21.54 23.01 2.34 +
026 1 31.75 23.49 24.97 2.34 +
027 1-1/8 34.93 27.05 28.53 2.34 +
028 1-1/4 38.61 27.82 30.61 2.34 +
029 1-1/4 38.10 30.81 32.39 2.34 +
030 1-1/2 42.80 33.89 36.88 3.25 +
031 1-1/2 42.80 33.89 36.88 2.34 +
032 1-3/4 52.38 42.93 45.93 2.34 +
033 2 58.60 48.44 51.39 2.34 +
034 2-1/4 69.85 54.89 58.30 2.34 +
035 2-1/2 70.36 58.04 61.09 2.34 +
036 2-1/2 73.03 60.58 63.63 2.34 +
037 2-3/4 77.72 64.39 67.44 2.34 +
038 3 79.50 66.68 69.98 2.34 +
039 3-1/2 90.17 76.08 79.38 2.34 +

Use + at the end of a row to keep that size. The list follows you to the other charts. Material and quantity can be set per size in the tray, and the enquiry form opens with those lines ready.

Both tables can be searched from the filter row under the headings, and the lookup below takes a size number or a thread size when you have neither table to hand.

Interactive Lookup

Type the size number from the drawing, or the thread size if the number has been lost. A number in the two hundreds searches the metric range, a number below a hundred the imperial range.



Thread sizes can be typed as M10, 1/2 or 3/8. Both the metric and the imperial range are searched at once.

Reading The Four Dimensions

Every bonded seal is specified by the same four values, and a replacement has to match all four, because the washer sits in a spot face that is already cut. D sets whether the washer fits inside the spot face. d and d1 describe the bore through the washer and through the bonded insert, and it is these two that decide whether the bead sits over the port rather than inside it. S sets how far the washer stands proud of the face before the fitting is tightened, and therefore how much the bead is compressed.

Burst pressure in the tables we work from is quoted per size, and it falls as the washer gets larger: the smaller washers in the metric range are rated around 1500 bar, the largest around 420 bar. The limit is set by the metal thickness and the spot face diameter, not by the rubber, so a thicker washer in the same size carries more.

What To Send With An Enquiry

  • The size number if you have it, for example 215 or 030
  • The thread size, for example M22 x 1.5 or 3/4 BSP, where the number is unknown
  • The spot face diameter and depth, if the port is non-standard or the washer is a replacement for an unmarked part
  • Metal finish, since plain steel, zinc plated and stainless are different parts at the same size
  • Quantity per size and per year

The bonded seals product page covers the construction, the metal options and the pressure and temperature envelope. If you are replacing a copper washer on an existing port, send the port dimensions as well as the number, because the spot face is what the seal has to fit.

Request a Quote

Questions We Get Asked

What is the difference between 215 and 225?
Both are metric washers with a 22 mm thread and the same outside diameter of 28 mm. They differ in bore and thickness, so one fits a spot face the other will not seat in. Use the lookup rather than assuming that neighbouring numbers are close enough.

Can a bonded seal replace a copper washer?
Yes, where the port has a flat spot face and the washer thickness suits the fitting. A bonded seal needs less torque than the copper washer it replaces, and the joint does not need re-torquing after the first heat cycle.

Which range do I need for a BSP port?
The imperial range, which covers BSP and inch threads from 001 to 039. The two hundred numbers are metric only, and a metric washer on a BSP port will sit off centre.

Do you make the self-centring version?
Yes, in both ranges. It is the same size number with a lip that locates the washer on the fitting, so it cannot slide off during assembly. Say which style you want when you ask for the quotation.

滚动至顶部