Silicone covers the two ends of the temperature scale that nothing else reaches: it stays flexible at −60 °C and it survives 200 °C without hardening. For a cold store, an oven door, a laboratory instrument or a medical device, that range is worth more than strength.
What silicone does not have is strength. Its tear resistance is the lowest of the five compounds, its compression set at temperature is only fair, and it swells in many oils and fuels. Silicone is chosen for temperature and for cleanliness, never for pressure or for a hard-working dynamic joint.
What Silicone Is
Silicone, VMQ in ISO 1629 terms, is a polysiloxane with a silica filler. The silicon oxygen backbone is why the compound stays flexible across such a wide range and why it does not age like a hydrocarbon rubber. The trade is mechanical: the same backbone gives low tensile and tear strength, high gas permeability, and no resistance to non polar oils. Phenyl content raises the low temperature limit further, and a fluorosilicone version buys fuel resistance at several times the price.
Properties At A Glance
The figures below are typical for a 70 Shore A compound of this class, which is the hardness most of our stock and most drawings call for. A 90 Shore A version of the same polymer will sit at the top of the hardness range and at the bottom of the temperature range.
| Property | Typical value | What it means |
|---|---|---|
| Hardness | 30 to 80 Shore A | 50 and 70 are the common drawing figures |
| Temperature range | −60 to +200 °C | Short excursions to 230 °C; special grades to −100 °C |
| Colour | Translucent to red, black, white | Colour is a marker, not a specification |
| Tensile strength | 6 to 10 MPa | The weakest of the five |
| Tear resistance | Poor | Damaged easily during fitting |
| Compression set | Fair | Noticeably worse than FKM above 150 °C |
| Relative cost | Moderate to high | Below FKM, well above NBR |
Where It Works
- Cold rooms, freezers and outdoor equipment that starts at −40 °C
- Ovens, heaters and hot air ducts up to 200 °C
- Food, pharmaceutical and medical equipment, in an approved grade
- Electrical and instrument enclosures, where the joint is static and dry
- Anywhere a non staining, odourless compound is required
Where It Fails
- Mineral oil, grease and fuel, which swell it
- Steam and hot water above about 100 °C
- Dynamic duty under pressure, where the low tear strength takes the ring apart
- Joints with sharp edges or a rough bore, which cut it during assembly
- High pressure gas service, where its permeability shows
Resistance To Common Media
Ratings are for the compound class at room temperature unless the note says otherwise, and they describe swelling, hardening and loss of strength together rather than one figure. A compound that swells 20 percent has already changed its squeeze.
| Medium | Rating | In practice |
|---|---|---|
| Hot air and oven atmospheres | Excellent | The reference application |
| Low temperature start-up | Excellent | Flexible at −60 °C in a standard grade |
| Water at room temperature | Good | Up to about 80 °C, then it degrades |
| Steam | Poor | Not a steam compound |
| Mineral oil and grease | Fair | Swells; silicone grease is the exception |
| Petrol and diesel | Poor | Fluorosilicone is the expensive answer |
| Dilute acids and bases | Fair | Depends on concentration and temperature |
| Ozone and weather | Excellent | Stable outdoors |
Compounds We Quote
We quote silicone from 30 to 80 Shore A, in general purpose and high temperature grades. Food contact grades to FDA 21 CFR 177.2600 and medical grades to USP Class VI are available on request with the certificate. Platinum cured silicone is the grade for anything that touches a product, because it avoids the peroxide by products that a sulphur or peroxide cure leaves behind.
Silicone is often specified for a colour rather than a property, in medical and food equipment where a red or white ring marks a particular line. That is a legitimate reason to buy silicone, and it is also the reason a quotation should name the hardness and the cure system as well as the colour.
Sizes And Standards
Choosing between compounds rather than specifying one? The O-ring material comparison puts all five side by side at 70 Shore A, with the temperature range and the media each one cannot take.
The size is a separate decision from the compound, and it is the one buyers most often get wrong. The four standard lists are on their own pages, each with a lookup that takes either the code or a pair of measured dimensions: AS568 (inch dash numbers), ISO 3601 (Class A and Class B metric), JIS B 2401 (P, G, S, SS and V series) and BS 1806 (British imperial numbers). If the drawing gives a size outside those lists, or a cord that is not standard, we mould to drawing.
What To Send With An Enquiry
- The size or dash number, and the standard it comes from
- The temperature range, both the working figure and the extremes
- Whether the seal contacts food, drinking water or a patient
- Hardness, and whether the joint is static or dynamic
- Any colour requirement, if it is a marker rather than a preference
What is the temperature range of silicone O-rings?
About −60 to +200 °C for a standard grade, with short excursions to 230 °C. It is the widest range of any compound on our matrix at both ends, which is why silicone is chosen for cold rooms and ovens alike.
Are silicone O-rings food safe?
In an approved grade, yes. We supply FDA 21 CFR 177.2600 and USP Class VI compounds on request, and platinum cured silicone where the application needs it. The certificate comes with the batch, not with the page.
Why do silicone O-rings tear so easily?
Low tear strength is inherent to the polymer. Fit them with a blunt tool and a little silicone grease, and avoid stretching them over threads or a sharp groove edge, which is where most silicone rings are damaged before they ever see service.
Can silicone be used in oil?
Only where the swelling is acceptable. Silicone swells in mineral oil and fuel, and the swelling softens it further. NBR is the oil compound; silicone is the temperature compound.
