A drawing that carries an O-ring number is only unambiguous inside the standard it came from. The same ring can appear as AS568-214 on an American drawing, as a 25 x 3.55 mm metric size on a European one, and as a JIS code on a Japanese machine, and the three are close enough to fit the same groove but not identical enough to ignore. This page sets out how each system identifies a size, and how to cross reference without creating a mismatch.
O.S Seals supplies rings to all of these systems. Send the code together with the inside diameter and cross section, and we will confirm what we will actually deliver.
The Systems at a Glance
| Standard | Origin | Units | How a size is written | What it fixes |
|---|---|---|---|---|
| AS568 | SAE, North America | Inch | Dash number, for example -214 | Inside diameter, cross section, tolerances, dash numbering |
| ISO 3601-1 Class A | ISO, international | Inch sizes, metric values | Same dash number as AS568 | The AS568 inch sizes, with the same tolerances |
| ISO 3601-1 Class B | ISO, international | Metric | Group letter plus four digits, for example C0250 | Metric inside diameters with five metric cord groups |
| JIS B 2401 | JSA, Japan | Metric | Series letter plus number, for example P22 or G45 | Five metric series by application, with their own tolerances |
| BS 1806 and BS 4518 | BSI, United Kingdom | Inch and metric | Inside diameter x cross section, in inches or millimetres | Legacy British sizes still quoted on older drawings |
| DIN 3771 | DIN, Germany | Metric | Inside diameter x cross section in millimetres | German metric sizes and tolerances |
Each of those lists is searchable on its own page: the AS568 chart, the ISO 3601 chart, the JIS B 2401 chart and the BS 1806 chart. All four take either the code or a measured inside diameter and cord.
AS568: the Dash Number System
AS568 is a list, not a formula. Each dash number is tied to one inside diameter and one cross section, from -001 at 0.029 in inside diameter up to -475 at 25.94 in. The first digit of the dash number gives the cross section series, so -110 and -210 share the last two digits but have different cords, 2.62 mm against 3.53 mm.
Two details catch buyers out. The 000 series contains three sizes with a thinner cord than the rest of the series, and the 900 series (tube fitting seals) sits outside the main numbering and outside ISO 3601 Class A. The full list, with the tolerance on every dash number, is on our AS568 size chart.
ISO 3601: Two Classes, Only One of Them Inch
ISO 3601-1 was written to hold both the American and the metric systems, and that is the source of most confusion. The two classes are not two tolerance grades of the same list. They are two different size lists.
- Class A is the AS568 inch list. Same sizes, same dash numbers, same tolerances. A -214 to Class A is the same part as an AS568 -214.
- Class B is a metric list. Inside diameters are metric and the cords are 1.80, 2.65, 3.55, 5.30 and 7.00 mm, which are close to but not the same as the inch cords of 1.78, 2.62, 3.53, 5.33 and 6.99 mm.
| Class B group | Cord (mm) | Cord tolerance | Inside diameter range (mm) | Code example |
|---|---|---|---|---|
| A | 1.80 | ±0.08 | 1.8 to 125.0 | A0250 = 25.0 mm ID |
| B | 2.65 | ±0.09 | 4.5 to 250.0 | B0092 = 9.2 mm ID |
| C | 3.55 | ±0.10 | 14.0 to 355.0 | C0250 = 25.0 mm ID |
| D | 5.30 | ±0.13 | 37.5 to 200.0 | D plus the ID in tenths of a mm |
| E | 7.00 | ±0.15 | 109.0 to 400.0 | E plus the ID in tenths of a mm |
The code carries the group letter and the inside diameter in tenths of a millimetre, padded to four digits. It does not carry the cord, because the cord is fixed by the group letter. Quality acceptance is a separate part of the standard, ISO 3601-3, with grades N, S and CS for surface imperfections.
Every Class B code, group by group, with its inside diameter and cord, is listed on our ISO 3601 size chart.
JIS B 2401: Five Series by Application
The Japanese standard splits its sizes by what the ring does rather than by cord alone. Each series has its own cord range, and the number in the code is a nominal figure, not the measured inside diameter.
| Series | Application | Cord range (mm) | Example code | Actual size of that code |
|---|---|---|---|---|
| P | General purpose, dynamic and static | 1.9 to 8.4 | P10 | 9.80 mm ID x 1.90 mm CS |
| G | Fixed and static joints | 3.1 to 5.7 | G25 | 24.40 mm ID x 3.10 mm CS |
| S | Small cross sections | 1.5 to 2.0 | S10 | 9.50 mm ID x 1.50 mm CS |
| SS | Sub-miniature sizes on a 1.00 mm cord | 1.0 | SS100 | 10.00 mm ID x 1.00 mm CS |
| V | Large sizes, vacuum flange service | 4.0 to 10.0 | V15 | 14.50 mm ID x 4.00 mm CS |
Note the gap between the code and the size: P10 is not a 10 mm inside diameter, it is 9.80 mm. Anyone who reads a JIS code as a metric dimension will order the wrong ring, which is why JIS drawings should be quoted with the dimension as well as the code.
The full P, G, S, SS and V lists, code by code, are on our JIS B 2401 size chart.
BS 1806, BS 4518 and DIN 3771
The British standards are usually written as a dimension pair rather than a code: BS 1806 in inches, BS 4518 in millimetres. They appear most often on legacy drawings from older British equipment, and a number of sizes overlap with AS568 while others do not. DIN 3771 is the German metric list and is normally written as inside diameter x cross section in millimetres.
For all three, treat the dimension as the specification and the standard number as the tolerance reference. If a drawing gives only a standard number and no dimension, ask for the dimension rather than converting from a table.
Our BS 1806 size chart lists 334 numbers, from 001 to 460, with the inch dimensions and their millimetre equivalents.
How to Cross Reference Without Creating a Mismatch
- Get both dimensions. Inside diameter and cross section, in one unit. A dash number without a size is not enough to convert.
- Match the cord first, then the diameter. The cord decides the squeeze. A ring with the right diameter and the wrong cord will leak or will not fit the groove at all.
- Check the tolerance class. AS568 and ISO 3601 Class A share bands. Class B and the JIS series have their own, and the difference can be wider than the cord difference.
- Check the groove, not just the ring. A metric groove is designed around a metric cord. If you fit an inch ring into it, the squeeze changes even when the ring measures close.
- Write both numbers on the order. Put the standard code and the dimensions on the purchase order, so a substitute cannot be supplied against the code alone.
Worked Examples
| Drawing says | Size | AS568 equivalent | What to watch |
|---|---|---|---|
| AS568-110 | 9.19 x 2.62 mm | Same, also ISO 3601 Class A 110 | ISO 3601 Class B nearest is B0092 at 9.2 x 2.65 mm, a different cord |
| AS568-210 | 18.64 x 3.53 mm | Same, also ISO 3601 Class A 210 | Nearest Class B is C0186 at 18.6 x 3.55 mm |
| Metric 25 x 3.55 mm | ISO 3601 Class B C0250 | -214 at 24.99 x 3.53 mm | Often used as a substitute, but the cord is 0.02 mm thinner and the tolerance class differs |
| JIS P25 | 24.70 x 3.50 mm | No equivalent | The 3.50 mm cord does not exist in AS568, so no dash number is correct |
The pattern is consistent: the diameters are frequently within a few hundredths of a millimetre, the cords are not. That is why a cross reference table built only on inside diameter produces so many field failures.
Frequently Asked Questions
Is ISO 3601 Class A the same as AS568?
Yes for the sizes and dash numbers. Class A is the AS568 inch list adopted into the ISO standard, and the tolerances match AS568. The 900 series is not included.
Can I replace a metric ring with the nearest AS568 size?
Only after checking the cord and the groove. In a static joint with generous squeeze it often works. In a dynamic or high pressure joint it usually does not, and it is not something to decide from a dash number alone.
What does the letter in a JIS code mean?
It is the series: P for general purpose, G for static joints, S for small cross sections, V for large and vacuum sizes. The number after the letter is a nominal inside diameter, not the measured one.
Do you supply to a metric drawing with no standard number?
Yes. Send the drawing and the dimensions, and we will make to the drawing rather than force it into a standard list.
Request a Quote
Send the code, the dimensions, the compound and the quantity. If the ring is going into an existing groove, tell us that too, because the groove is often the part that decides whether a substitution is safe.
