DIN 3760 is the German standard for radial shaft seals, and it is the reference behind most metric oil seal drawings in Europe and Asia. It fixes the type designations, the nominal dimensions, and the tolerances. What it does not fix is whether a seal will last in your machine, because that depends on the medium, the temperature, the speed, and the condition of the bore and shaft.
The letter code is short: A, AS, B, BS, C and CS. Three of them describe the outer construction, and the S suffix adds a dust lip. This page explains what each type is for, how to pick one from the housing you have, and what to put on the drawing so the seal you receive is the seal you specified.
Three Outer Constructions, One Suffix
The base letter is decided by how the outside of the seal is built, because that surface carries the static seal and holds the seal in the bore.
- A: elastomer covered outside diameter. The metal insert is fully embedded in rubber, so the bore sees only rubber. The rubber compresses and seals against the bore, which makes this the most forgiving type on a bore that is not perfect.
- B: bare metal outside diameter. The lip is moulded to the inner part of a metal case, and the case presses directly into the bore. It centres accurately and goes in with less force, but it needs a clean, accurate bore.
- C: metal case with a reinforcing cap. A second metal shell inside the case makes the seal much stiffer. Used on larger diameters and on seals that get rough handling during installation.
- The S suffix (AS, BS, CS) adds a second lip on the air side. It keeps dust, water splash and grit away from the main lip. It is not a pressure lip and does not increase the pressure rating.
Type Spectrum: A, AS, B, BS, C, CS
| Type | Outside diameter | Dust lip | Bore requirement | Best used on | Watch out for |
|---|---|---|---|---|---|
| A | Rubber covered | No | Tolerant of finish and light ovality | Aluminium and light alloy housings, reworked or worn bores, split housings, gearbox covers | Higher press-in force; the seal can cock if it is not pressed squarely |
| AS | Rubber covered | Yes | Tolerant of finish and light ovality | Exposed positions where dust or water splash reaches the seal, agricultural and off-highway equipment | The dust lip needs grease between the lips at assembly, or it runs dry |
| B | Metal | No | H8 bore with good finish | Precise steel and cast iron bores, repeated OEM assembly, electric motors and gear units | Metal to metal contact weeps on a coarse or porous bore |
| BS | Metal | Yes | H8 bore with good finish | Precise bores in dusty or wet locations | Same bore sensitivity, plus the dust lip needs grease |
| C | Metal with reinforcing cap | No | H8 bore with good finish | Large diameters, heavy duty equipment, seals that are handled often | Stiffer case is less forgiving of a bore that is out of square |
| CS | Metal with reinforcing cap | Yes | H8 bore with good finish | Large diameters in contaminated service | Same as C, and the grease space between the lips must be filled |
Choosing the Type From the Housing
In practice the bore decides more than the shaft does. Work through these in order:
- Is the housing a light alloy, or has the bore been reworked? Use A or AS. A metal case on an aluminium bore can weep when the housing grows with heat, and a bore that has already had two seals pulled out of it is rarely round enough for a metal case.
- Is the bore a precise steel or cast iron bore, machined to H8? B or BS gives better centring and easier installation, and that matters on a production line.
- Is the diameter large, or is the seal exposed to impact during assembly? C or CS, because the reinforcing cap resists deformation.
- Is the seal exposed to dust, mud or water splash? Add the S suffix. On a gearbox in a clean plant it adds nothing, on a wheel hub or a track roller it is the difference between one season and three.
- Is the housing split through the bore? A or AS. The rubber outside bridges the joint line, while a metal case turns the step at the joint into a leak path.
Dimensions: d, D and b
An oil seal is written as three numbers, for example 40 x 62 x 8: shaft diameter, housing bore diameter, and width. All three are nominal figures, and all three carry tolerances. Two seals that read 40 x 62 x 8 from different makers can differ in lip geometry, case thickness and spring force, so the dimension triple identifies the envelope, not the part.
| Dimension | What it is | How to measure it on a used seal | Common mistake |
|---|---|---|---|
| d | Shaft diameter at the lip contact line | Measure the shaft, not the old seal, and measure where the lip runs rather than in the worn groove | Reading the seal bore after it has taken a set, which gives a figure 0.2 to 0.5 mm small |
| D | Housing bore diameter | Measure the bore in two directions at 90 degrees | Measuring a bore that has been distorted by a previous seal, or measuring over paint |
| b | Seal width, and the depth of the bore | Measure the old seal width and the bore depth | A seal wider than the bore will not seat; a seal much narrower can move axially |
Fits and Surface, the Part DIN 3760 Does Not Do for You
The standard sets the seal, not the housing. A DIN 3760 seal in a bore that is one grade too wide will leak around the outside diameter, and no type letter will save it. The usual requirements are:
- Housing bore H8, with a lead-in chamfer so the seal is not cut as it enters.
- Shaft h11 for general service, tighter where speed is high.
- Shaft ground without a lead, typically Ra 0.2 to 0.8 µm. A spiral from turning pumps oil along the shaft and looks exactly like a lip failure.
- Shaft hardness typically 30 HRC or above, more on high speed shafts, so the lip does not wear a groove.
- Bore finish Ra 3.2 µm or better, with no axial scratch across the seal seat.
- Square installation, so the lip runs perpendicular to the shaft. A seal pressed in at an angle leaks on one side only, which is a useful diagnostic sign.
The rubber seal tolerance guide covers the tolerance side in more detail.
DIN 3760, ISO 6194 and Trade Codes
DIN 3760 is technically aligned with ISO 6194-1, which describes rotary lip seals with elastomer sealing elements, so a drawing that cites either standard describes the same family of seals. What differs is the letter code, because manufacturers add their own trade designations on top. Codes such as TC, SC, TB and TA are used in catalogues and on boxes, and they are not consistent between makers: the same two letters can mean a rubber covered seal to one supplier and a metal cased double lip seal to another.
That is why the DIN 3760 letter should be the reference, backed by the three dimensions. If a customer sends a photo of a box with only a trade code on it, we identify the seal from the dimensions and the outside construction, not from the code.
Installation Rules That Decide Seal Life
- Protect the lip. Cover keyways, splines and threads with tape or a sleeve before the seal passes over them. A single nick in the lip is a leak.
- Lubricate the lip and the bore. Clean oil or grease on the lip, and a thin film on the outside diameter of a metal cased seal. Never grease the outside of a rubber covered seal to make it slide in, it can cause the seal to back out.
- Press on the outer edge, squarely. Use a flat driver or a press plate of the right diameter. Hammering on the case distorts it and loads the lip.
- Fill the space between the lips on AS, BS and CS types with grease before installation.
- Check the direction where the lip is asymmetric or the seal is marked with a rotation arrow. Fitting it backwards gives a short life and a persistent weep.
What to Send for a Quotation
- The three dimensions, d x D x b, or the number stamped on the old seal
- The type, A, AS, B, BS, C or CS, if the drawing names one
- Compound and hardness, or the medium and working temperature if the compound is open
- Shaft speed and whether the joint runs under pressure
- Quantity, and whether the demand repeats
- A photo of the old seal from both sides, where the type is not known
Our rotary shaft seal range covers the standard types in NBR, FKM, HNBR, EPDM and silicone, and custom profiles are produced to drawing or sample.
Frequently Asked Questions
What is the difference between type A and type AS?
The dust lip. A has one sealing lip, AS has the same lip plus a secondary lip on the air side. Everything else, including the outside diameter, is the same.
Can I use a B instead of an A in an aluminium housing?
It will press in, but a metal case on aluminium can weep as the housing expands with heat, and the bore is more easily damaged at the next replacement. A or AS is the safer choice there.
Does the S suffix make the seal suitable for pressure?
No. The dust lip excludes contamination. Pressure capacity comes from the lip profile and the support behind it, and standard DIN 3760 seals are for low pressure service only.
What does TC mean?
It is a trade code, not a DIN type, and it means different things to different makers. Send the dimensions and a photo, and we will confirm the construction rather than guess from the letters.
Request a Quote
Send the dimensions, the type if known, and the working conditions. If you are replacing a seal that failed early, tell us how it failed: a leak from the lip, a leak from the bore, or a torn dust lip each point to a different fix.
