Most seal complaints that reach a supplier are not material failures. They are dimensional: a ring that measures inside the standard band but outside the band the groove was designed for, an oil seal pressed into a bore that is one tolerance grade too wide, or a drawing that asks for a tolerance the moulding process cannot hold. This guide covers the three tolerance systems that decide whether a rubber seal fits: the moulded part tolerance, the O-ring dimensional tolerance, and the housing and shaft fits the seal sits in.
O.S Seals quotes against the drawing tolerance and states on the quotation which class we will hold. Where a drawing gives no tolerance at all, we agree one before the tool is cut, because that decision cannot be changed later without a new mould.
Three Systems That Are Often Confused
| System | What it controls | Where it comes from | What it does not control |
|---|---|---|---|
| Moulded part tolerance | Any dimension on a rubber part: diameter, width, wall thickness, flatness of a moulded face | ISO 3302-1, classes M1 to M4 | Whether the part seals. It only says how close to the drawing it is. |
| O-ring dimensional tolerance | Inside diameter and cross section of a standard ring | AS568, ISO 3601-1 Class A and Class B | Groove design, squeeze, or material hardness |
| Housing and shaft fit | The bore the seal presses into and the shaft it runs on | ISO fits (H8, h11), plus surface and hardness requirements in DIN 3760 and ISO 6194 | The seal itself. A good seal in a bad bore still leaks. |
A seal drawing usually needs all three. The ring tolerance alone does not describe the part, and the housing fit alone does not describe the seal.
ISO 3302-1: Tolerances for Moulded Rubber Parts
ISO 3302-1 is the standard behind most rubber part drawings. It defines four tolerance classes, from M1 for precision moulding to M4 for coarse commercial work, and it separates two kinds of dimension:
- Fixed dimensions (F): dimensions formed within one half of the mould, so flash and clamping do not affect them.
- Closure dimensions (C): dimensions that cross the parting line, so flash thickness and clamp force add to the variation. The permitted deviation is always wider than for a fixed dimension of the same size.
Typical published values are below. They apply to solid rubber mouldings, and the class is chosen per dimension, not per part: a part can hold M2 on a sealing face and M3 on a cosmetic edge.
| Nominal dimension (mm) | M1 F | M1 C | M2 F | M2 C | M3 F | M3 C | M4 |
|---|---|---|---|---|---|---|---|
| over 0 to 4 | ±0.08 | ±0.10 | ±0.10 | ±0.15 | ±0.25 | ±0.40 | ±0.50 |
| over 4 to 6.3 | ±0.10 | ±0.12 | ±0.15 | ±0.20 | ±0.25 | ±0.40 | ±0.50 |
| over 6.3 to 10 | ±0.10 | ±0.15 | ±0.20 | ±0.20 | ±0.30 | ±0.50 | ±0.70 |
| over 10 to 16 | ±0.15 | ±0.20 | ±0.20 | ±0.25 | ±0.40 | ±0.60 | ±0.80 |
| over 16 to 25 | ±0.20 | ±0.20 | ±0.25 | ±0.35 | ±0.50 | ±0.80 | ±1.00 |
| over 25 to 40 | ±0.20 | ±0.25 | ±0.35 | ±0.40 | ±0.60 | ±1.00 | ±1.30 |
| over 40 to 63 | ±0.25 | ±0.35 | ±0.40 | ±0.50 | ±0.80 | ±1.30 | ±1.60 |
| over 63 to 100 | ±0.35 | ±0.40 | ±0.50 | ±0.70 | ±1.00 | ±1.60 | ±2.00 |
| over 100 to 160 | ±0.40 | ±0.50 | ±0.70 | ±0.80 | ±1.30 | ±2.00 | ±2.50 |
| over 160 | 0.3% | 0.4% | 0.5% | 0.7% | 0.8% | 1.3% | 1.5% |
Values are the commonly published ISO 3302-1 moulding table, in millimetres unless a percentage is shown. Check the current edition of the standard before you release a drawing on the strength of this table, and confirm with us that the class is achievable for your geometry.
Hardness is toleranced separately, normally ±5 Shore A around the nominal figure. A 70 Shore A compound can be supplied at 65 or 75 and still meet the specification, which is why hardness alone is a poor way to compare two suppliers.
What Decides Whether a Tolerance Is Achievable
- Mould type. Compression moulding is the most economical and the least precise. Transfer moulding sits in the middle. Injection moulding holds the tightest class and the most consistent flash.
- Compound shrinkage. Every elastomer shrinks after cure, and the amount depends on the compound, not just the polymer family. A tool cut for an NBR 70 compound will not produce the same dimension in FKM 75.
- Hardness. Soft compounds below about 50 Shore A deform under measurement and hold a wider band in practice. Very hard compounds above 85 Shore A are difficult to deflash without marking an edge.
- Wall thickness and metal inserts. Thick sections and bonded inserts add shrinkage variation, so the same class gives a wider real spread than on a thin plain ring.
- Flash and deflashing. A closure dimension includes flash unless the part is deflashed. ISO 3302-1 also defines flash classes, so it is worth quoting one on a drawing where flash matters, for example on a sealing face.
O-Ring Tolerances: Cord and Diameter
For standard O-rings the tolerance is part of the size standard, which is why an AS568 dash number is a complete description of the geometry. The cord tolerance depends on the nominal cross section:
| Nominal CS (in) | Nominal CS (mm) | Cord tolerance (in) | Cord tolerance (mm) | Series |
|---|---|---|---|---|
| 0.040 | 1.02 | ±0.003 | ±0.08 | 000 (-001 to -003) |
| 0.070 | 1.78 | ±0.003 | ±0.08 | 000 |
| 0.103 | 2.62 | ±0.003 | ±0.08 | 100 |
| 0.139 | 3.53 | ±0.004 | ±0.10 | 200 |
| 0.210 | 5.33 | ±0.005 | ±0.13 | 300 |
| 0.275 | 6.99 | ±0.006 | ±0.15 | 400 |
The inside diameter tolerance is not a fixed number either. It grows with the diameter, because a larger ring has more mould and more shrinkage to control. A -010 with a 6.07 mm inside diameter is toleranced around ±0.13 mm, a -214 at 24.99 mm around ±0.25 mm, and a -425 at 113.66 mm around ±0.84 mm. ISO 3601-1 Class A uses the same bands as AS568. Class B is a wider class applied to metric sizes, and it is the class that causes most cross reference mistakes, because the number looks equivalent and the band is not.
The full size list with the tolerance on every dash number is on our AS568 O-ring size chart.
Oil Seal Fits: Bore, Shaft and Surface
An oil seal is a press fit in the bore and a running fit on the shaft, so its performance depends on fits the seal does not control. The values below are the fits seal makers normally ask for on a DIN 3760 or ISO 6194 seal, and they apply to the housing and the shaft, not to the seal.
| Feature | Typical requirement | What goes wrong when it is missed |
|---|---|---|
| Housing bore | H8, with a lead-in chamfer of about 15 degrees | Bore too tight shears the outside diameter; too loose and the seal creeps or weeps around the case |
| Shaft diameter | h11 for general service, tighter where speed is high | Too large preloads the lip and burns it; too small and the spring cannot follow the shaft |
| Shaft surface | Ground, without a lead or spiral pattern, typically Ra 0.2 to 0.8 µm | A turning mark pumps oil along the groove and the seal leaks from day one |
| Shaft hardness | Typically 30 HRC or above, higher on high speed shafts | A soft shaft wears a groove under the lip and no replacement seal will hold |
| Bore surface | Ra 3.2 µm or better, no axial scratches | A scratch across the bore gives a leak path outside the seal |
| Concentricity and runout | Bore to shaft, within the tolerance the seal maker states for the size | Runout makes the lip work unevenly and shortens life at speed |
These are reference values from common seal practice. For a specific application, the seal maker’s catalogue data for that profile and size governs, especially at high speed or with pressure.
For type selection by bore condition, see our DIN 3760 oil seal types guide.
How to Put Tolerance on a Rubber Seal Drawing
A drawing that says only “70 Shore A NBR, 40 x 62 x 8” leaves the supplier to choose the tolerance, and two suppliers will then quote two different parts. Three lines remove the ambiguity:
- Size and class. For a standard O-ring, quote the dash number and the tolerance class, for example AS568-214, Class A. For a moulded part, give the nominal dimensions.
- General tolerance. Add the ISO 3302-1 class, for example “general tolerances ISO 3302-1 M2, closure dimensions M3”.
- Critical dimensions. Dimension the sealing face, the lip, or the groove separately with its own tolerance rather than relying on the general note.
Where a dimension is functional, tolerancing it tighter than M2 usually adds cost without adding life. Where it is not functional, tolerancing it at all is unnecessary. We review drawings before quoting and will tell you which dimension is driving the price.
Inspection and Acceptance
Dimensional inspection covers the inside diameter, the cross section in two directions, and the overall height or width where the part has one. Hardness is checked on the compound, not on the finished part, because a curved surface reads low. Appearance is judged against ISO 3601-3 for O-rings, which defines three grades of surface imperfection: grade N for general purpose, grade S for demanding industrial and aerospace work, and grade CS for critical service. If your drawing does not name a grade, the inspector applies grade N.
Frequently Asked Questions
Can you hold M1 on a compression moulded part?
Rarely, and not on a large part with thick sections. M1 needs a ground mould, tight temperature control, and usually injection moulding. For most seals M2 on the functional dimensions is the practical choice.
Is a wider tolerance cheaper?
Sometimes, but the bigger cost driver is the mould and the process. A part that fails in service because the tolerance was widened to save a few percent is the more expensive option.
My drawing has no tolerance. What happens?
We ask before quoting. If you have no preference, we propose M3 general with M2 on the sealing dimensions and state it on the quotation so both sides are working to the same document.
Does a Class B O-ring fit a Class A groove?
It can fit, but the squeeze will vary more across the batch. On a static joint with generous squeeze that is often acceptable. On a dynamic or high pressure joint it is not, and the drawing should name the class.
Request a Quote
Send the drawing or the dimensions, the compound, the medium and temperature, and the tolerance class if your drawing names one. We will confirm what we can hold before production.
